WTW7500GC0 Whirlpool - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys

As women, myself and my daughter completed this fairly simple repair. The replacement washer plate was top quality and included the washplate replacement screw. Additionally, we purchased a tube of lock tight to further secure bolt placement. The most difficult part of the repair is to disengage old screw and securely replace with new one. Very pleased with fast delivery Excellent customer service and top quality part.
Thanks

The valve is a 4 solenoid valve, which has Temp. sensor molded into the valve body mixer center outlet. No mention of it in the troubleshooting. it has a 2 pin plug. it was shorted zero ohms.
New one measure open infinity. I also purchased the control module as the troubleshooting said to if solenoid checked good which all 4 read 1310 ohms , i purchased and replaced control module, no help. the guide is outdated for these new high tech washers. If this happens again. I will just unplug the 2 pin plug on bottom of valve assembly. By the way the 2 clips that hold the washer top in place are very difficult to remove and re install.

Removed two screws on back of lid to raise top removed tub one bolt and one spanernut pulled tub lowered top reinstalled screws laid washer down to get to bottom of washer unplugged wiring removed four bolts pulled gear box and motor removed motor from gear box installed motor on new gear box reassemble washer

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

If you take the back off the machine, it's a lot easier to detach the control bridge. Saved a lot of time and did not need to stretch your fingers

Washer would start cycle and return a CL error. No water would flow into the tub. Researched problem and probable cause. Ordered new water inlet valve. Once received, disconnected water hoses and electric plug and removed rear upper access panel (5 screws). Used thin putty knife under sides of front control panel to disengage spring clips. Once access to the faulty valve was attained, removed electrical harness and valve mounting screws. Installation of new valve was reverse process. Figuring out how to raise the front panel for access to the valve was most difficult. Found a YouTube video showing how; it was easy from there. Entire replacement took about 30 mins max.

DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.

UNPLUG WASHER FROM WALL PLUG
Watch u tube on how to remove top and also cover on top circuit compartment
First find the service book taped inside front. PLUGand read to read codes
call up the error codes flashing
the code indicated a defective lid latch.UNPUG WASHER
went through testing the switch one of the contacts was defective and intermittent.
UNPUG WASHER unpug J connect from circuit board remove wiring and connect from lid
new wiring harness goes back same as old one and mount new lid switch. done

My husband watched numerous YouTube videos before tackling it.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.

I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May