WTW5000DW1 Whirlpool Washer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Touch-Up Paint - White – Part Number: 72017
No Longer Available
Touch-Up Paint - White
★★★★★
★★★★★
(23)
Part #72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
Drive Hub Kit – Part Number: W10528947
$39.32
In Stock
Drive Hub Kit
★★★★★
★★★★★
(38)
Part #W10528947
This drive hub kit helps your washer spin and agitate properly by connecting the basket to the motor. If your washer isn’t spinning, is noisy, or wobbles too much, this part might be the fix. It’s a simple DIY repair with easy-to-follow instructions and usually includes everything you need to get your washer working again.
Washing Machine Suspension Rod Kit – Part Number: W10780048
$87.93
In Stock
Washing Machine Suspension Rod Kit
★★★★★
★★★★★
(60)
Part #W10780048
This washing machine suspension rod kit includes 4 suspension rods, 4 suspension balls, and 4 bushings to stabilize the washer tub and minimize vibrations during operation. If the washer shakes or vibrates excessively, replacing the suspension rods may resolve the issue. Installation requires safety precautions, such as unplugging the appliance and wearing work gloves.
Washer Drive Pulley – Part Number: W10721967
$53.48
In Stock
Washer Drive Pulley
★★★★★
★★★★★
(20)
Part #W10721967
If your washer is noisy, spins slowly, or leaves clothes soaking wet, this splutch cam kit might be the fix. It helps your machine switch between washing and spinning by connecting the motor to the basket. The kit includes everything you need—clutch parts, pulley, gear, and more—but make sure it fits your model before ordering. It’s a simple repair that can get your washer back to working like new.
Washer Drive Belt – Part Number: WPW10006384
$40.34
In Stock
Washer Drive Belt
★★★★★
★★★★★
(13)
Part #WPW10006384
If your washer isn’t spinning or making strange noises, the drive belt might be worn out. This genuine replacement belt connects the motor to the drum, helping it spin and tumble your clothes properly. It fits many Whirlpool, Maytag, and Kenmore models, but be sure to check your model number before ordering. A broken belt can also cause a burning smell, so replacing it can get your washer back in shape and running smoothly.
Washing Machine Door Lock Assembly – Part Number: W11307244
$178.47
In Stock
Washing Machine Door Lock Assembly
★★★★★
★★★★★
(17)
Part #W11307244
This lid switch assembly is for a top load washer. The lid switch assembly detects if the washer lid is open or closed and prevents the washer from spinning when the lid is open.
Suspension Rod Kit – Part Number: W11130362
$157.74
In Stock
Suspension Rod Kit
★★★★★
★★★★★
(18)
Part #W11130362
This suspension rod kit is a genuine OEM replacement kit that is compatible with various models of washing machine. The kit is responsible for supporting the inner tub of the washing machine and absorbing any excessive vibrations and movement caused during the washing and spinning cycles. This helps to protect the tub and interior of the washer from damage. If the suspension rods in your washer are faulty, you will likely notice loud banging, knocking, or scraping sounds as the tub makes contact with the washer cabinet. Each kit includes four suspension rods and springs as well as the suspension ball cups. It is advised you replace all suspension rods at the same time, as they tend to wear at similar rates.
Water Inlet Valve – Part Number: W11210459
$101.64
In Stock
Water Inlet Valve
★★★★★
★★★★★
(23)
Part #W11210459
This water inlet valve is for washers. The water inlet valve controls the water flow into the washer. Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
ACTUATOR – Part Number: W11481722
$117.10
In Stock
ACTUATOR
★★★★★
★★★★★
(4)
Part #W11481722
This shift actuator is an essential component in washing machines, responsible for switching the motor between spin and agitate modes while also communicating spin speed to the control board. A malfunctioning actuator can lead to improper spinning or agitation and may trigger error codes. Made primarily of durable plastic, it features an integrated 120V/60Hz/2.8W motor for reliable performance. This OEM part is sold individually and is compatible with a variety of washer models. For safety, always disconnect power before installation and follow manufacturer guidelines for replacement.
Screw, 8-16 x 1.000 – Part Number: WP8533953
$9.85
In Stock
Screw, 8-16 x 1.000
Part #WP8533953
Sold individually.
Washer Drain Hose – Part Number: W11244231
$37.25
In Stock
Washer Drain Hose
★★★★★
★★★★★
(4)
Part #W11244231
The drain hose carries used water from the washer to your house drain.
Hose Clamp – Part Number: WP285655
$15.68
In Stock
Hose Clamp
Part #WP285655
This hose clamp is sold individually.

Questions And Answers for WTW5000DW1

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sandi - For model number WTW5000DW1
February 23, 2020
Washer is making a grinding sound and will not agitate or spin
Chris Boyle Profile
Hello Sandi, thank you for your question. There are a few parts we would recommend checking to determine the issue. They are Drive Hub Kit Part Number: W10528947, Washer Drive Pulley Part Number: W10721967, Shift Actuator - 6 Pin Part Number: W10913953. If those parts are ok, the issue is probably the gearcase and transmission Part Number: W11035751. I hope this helps.
17 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Jeff - For model number WTW5000DW1
December 5, 2019
The washer will start and pump in water but will stop after about a minute. It won't continue to the wash cycle. If i open and close the lid the water will start pumping again but stop about 30 seconds to a minute later.
Chris Boyle Profile
Hello Jeff, Thank you for the question. This could be an issue with a defective Door Lock, PartSelect Number PS12704713. This lid switch assembly is for a top load washer. The lid switch assembly detects if the washer lid is open or closed and prevents the washer from starting the cycle. Hope this helps!
$178.47
In Stock
Washing Machine Door Lock Assembly
13 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Mary - For model number WTW5000DW1
February 12, 2020
Sensor light blinking off and on can not start a wash. Not draining water in washer.
Chris Boyle Profile
Hi Mary, thank you for your question. When your appliance is not starting there are a few parts that you may want to check, however you could try and do a reset on your machine. Generally how to do that is unplug your appliance for 30 minutes and then plug it back in again. If the issue continues the first part to take a look at would be your door lock: PS12704713. If that part is fine then you may need to take a look at your switches or control board for being the issue. Good luck with your repair.
7 people found this instruction helpful.
Was this helpful?
Thank you for voting!
PAUL - For model number WTW5000DW1
November 28, 2019
We had a power surge. Unit will not turn on. I there a fuseable link? Does the motor have a reset?
Chris Boyle Profile
Hello Paul, Thank you for the question. Normally this indicates the control board PartSelect Number PS12114296 had shorted out by the surge and may need to be replaced. Hope this helps!
$456.09
In Stock
Washer Electronic Control Board
6 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Stephen - For model number WTW5000DW1
February 7, 2020
Starts to spin or agitate, then stops. Is this the transmission?
Chris Boyle Profile
Hello, Thank you for your question. Here is some information on how to test the parts in the washer to determine if the issue is the agitator or the transmission: https://www.partselect.com/Repair/Washer/Not-Agitating/ . We hope this helps, good luck with this repair.
4 people found this instruction helpful.
Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3

Common Symptoms of the WTW5000DW1

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Violent shacking in spin mode.
189 of 230 people found this instruction helpful.
  • Terry from Homosassa, FL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Watched a video on the internet.
Was this helpful?
Thank you for voting!
Noise on bottom of Washer louder as time went on. 1 1/2 years
95 of 129 people found this instruction helpful.
  • Jerry from WALLA WALLA, WA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Was this helpful?
Thank you for voting!
Hub had warn its grooved teeth off and washer wouldnt agitate
66 of 93 people found this instruction helpful.
  • Allison from RICHFORD, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed.
Was this helpful?
Thank you for voting!