These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
Sits in between the agitator base and upper agitator.
$14.16
In Stock
Questions And Answers for WTW4800XQ1
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Stacey
December 4, 2019
The washers lock lid light stays on and will not fill up with water please help not sure what to do or how to fix this.
For model number WTW4800XQ1
Hello Stacey and thanks for writing.
It sounds like a faulty lid latch assembly PS3497627 and/or the lid latch strike PS11750882 check and replace if needed. It is recommended to replace both parts at the same time. We hope this helps. Please contact us anytime.
Hello Lillian, thank you for reaching out to PartSelect. We have researched and found that the capacity of your model is 3.4 cubic feet. We hope this information helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Gerald
December 2, 2019
Will not spin all the water out on a full load. It will spin all water out on a half of a load.
For model number WTW4800XQ1
Hello Gerald, Thank you for the question. I suggest checking the Belt PartSelect Number PS11747978 for wear or damage. Hope this helps!
Hi Leonad, thank you for reaching out. We would recommend checking the washer control board, part number PS10062753. It manages the washer's functions such as filling, washing, draining and spinning. You may need to replace it to fix the issue. We hope this sorts out your problem!
My washer is not running cycles. For example when you start a wash it flashes for 4 minutes then stop and open the lid. You then have to press the start button again for it to fill up. Then it opens the lid again. After pressing start again it runs for about 12 minutes then stop again this goes on after every cycle until the wash is completed.
Any recommendations?
For model number WTW4800XQ1
Hello Monica, thank you for contacting us. A faulty lid latch switch, part number PS3497627, could interrupt the operation of the washer from advancing in the cycle. A faulty water inlet valve could cause this as the washer is not able to fill with water and the cycle is ending. Check your water inlet valve part number PS11753661, and valve, part number PS11754670 to see if they are working or if there are any obstructions in them. If they are good, you may need to replace your control board, part number PS10062753. We hope this solves your problem!
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs. Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out). Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble