This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
This temperature sensor is for refrigerators.
The temperature sensor senses the temperature inside the refrigerator and sends information to the electronic control.
Unplug the refrigerator and s...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nathan
March 26, 2023
I have a whirlpool refrigerator in my camper. Everything works on it as it was brand new installed in the camper before purchase. We gave it the 24 hour allotted time to get cold but still is remaining at room temp.
One of the things I had seen was that if it is not level it won't run? is this true?
For model number WRT519SZDM00
Hi Nathan, thank you for your question. For the refrigerator to run function, it needs to be levelled properly. If your refrigerator is not levelled, you may need the levelling leg, part number PS11731286. We hope this helps!
Over the past couple of weeks, I noticed that things in the freezer started to defrost. I turned down the temp, and now the freezer freezes, but so does the fridge. What part should I look at replacing/ testing? Thanks
For model number WRT519SZDM00
Hello Rebecca, thank you for getting in touch. Based on our understanding of the issue, we would suggest you replace the thermistor, part number PS12745758. We hope this solves your problem!
I have replaced both thermistors, hasn't changed anything. Both the freezer and refrigerator are too warm on the first setting. On the second setting, both compartments freeze. freezer to about -4 and refer drops to 24-28 degrees. unit is approx 8 years old.
What else should I be looking at?
Thanks for any assistance you can give.
For model number WRT519SZDM00
Hello Francis, thank you for reaching out. Based on our understanding of the issue, we would suggest checking the control board, part number PS11756925, to solve the problem. Glad to be of assistance!
Hello Glenn, thank you for getting in touch. In order to reverse the doors, you may need the door reversal kit, part number PS11725548. Glad to be of assistance!
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
The reason I repaired it myself was because the repairman that diagnosed the problem.didn't come back in two weeks. The evaporator fan sits behind a vented wall in the freezer and directs cold air into freezer and refrigerator.I removed the ice make assembly first and then the freezer wall held in place by two sheet metal nuts. Then removed wires from fan motor. Removed the fan blade from fan motor,which was press fitted on,then removed fan motor from bracket assembly(make sure and retain the two vibration rubber washers on back and front of motor. Reinstall new motor with vibration washers and press fan blade on new motor. Install in bracket assemble and reassemnble.
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.