This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This clear plastic door bin attaches to the inside of the refrigerator door and holds jars and bottles. Door bins can crack and break due to frequent and heavy use, and faulty bins should be replaced.
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
Sold individually. Hardware not included. Roller only.
$44.00
In Stock
Questions And Answers for WRT511SZDM00
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barbara
February 25, 2023
I do not see the light bulb for the freezer listed. Where do I obtain the replacement bulb?
For model number WRT511SZDM00
Hello Barbara, thank you for your question. We sell the the Freezer light is PS16555179 on our website. We hope this helps.
Freezer works, but refrigerator doesn’t. I defrosted freezer, even the small holes in the ceiling of the refrigerator; also i cleaned all filters in the back, still it has the same problem. And suggestions?
For model number WRT511SZDM00
Hello Bojana, thank you for inquiring. You will most likely need to replace the Evaporator Fan Motor, part number PS11740359 for your model refrigerator to fix this. Good luck with your repair!
Was this helpful?
Thank you for voting!
Shirley
November 5, 2023
need lightbulb for freezer
For model number WRT511SZDM00
Hi Shirley, thank you for reaching out. The part you are looking for is the light bulb, part number PS16555179. We hope this is helpful!
Hello Lena, thank you for reaching out. According to our understanding of the issue, we would recommend replacing the freezer door gasket, part number PS2355528. It creates a seal around the door to prevent warm air from entering the freezer compartment. Glad to be of assistance!
I need the bracket or frame that holds the meat drawer.
For model number WRT511SZDM00
Hello Mark, thank you for contacting us. The part you are looking for is the shelf, part number PS11731608. If you need help placing an order, customer service is open 7 days a week!
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
The reason I repaired it myself was because the repairman that diagnosed the problem.didn't come back in two weeks. The evaporator fan sits behind a vented wall in the freezer and directs cold air into freezer and refrigerator.I removed the ice make assembly first and then the freezer wall held in place by two sheet metal nuts. Then removed wires from fan motor. Removed the fan blade from fan motor,which was press fitted on,then removed fan motor from bracket assembly(make sure and retain the two vibration rubber washers on back and front of motor. Reinstall new motor with vibration washers and press fan blade on new motor. Install in bracket assemble and reassemnble.
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.