WRF954CIHB02 Whirlpool Refrigerator - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

Purchased new motor from Partselect.com. When it arrived it came with a new rubber washer that fitted on top of new motor that was not on old motor, that how water got into old motor. However, the instruction sheet did not give info on how to access the proper way to the motor that is the door. Not wanting to damage the freezer door assy. called in a tech who made it look easy, but even he had a little problem locating access panel that was directly under the motor in the freezer side of the door. After that it was a piece of cake.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

Removing the old unit was difficult. The light was clearly designed for installation not for ease of repair. Since I was concerned about marring the surface of the refrigerator I used a paint scraper to get under the lip of the light and another smaller paint scraper to lift the unit away from the body of the refrigerator. It does not just "pop off". I eventually did get it free without any damage to the wall of the refrigerator. The repair was then very easy. There was a connector that was easy to separate allowing for the removal of the old unit without cutting any wires. The new unit had a mating connector, which easily connected to the old connector in the refrigerator. After some pushing I was able to install the new unit into the hole in the refrigerator. It does not exactly "snap in".

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

researched on line and found the wiring was in series and I the suggestion was to replace the first light in the series that was in the freezer. Ordered the replacement light board and took out the existing light and pooped in the new one. Lights now all work! 15 minutes at tops.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Remove first cover remove the light panel and replace it
Install everything back...

From Donna Turner acct # 190766

I ordered Refrigerator/freezer light board PS11702378

You substituted for a single light module

I troubleshooted and decided to order from your company the light board. You changed my order. I researched what you sent and thought, ok, we'll identify the one light that is out and replace only that...

My paid electrician spend well over an hour inside the frig, and confirmed that all 3 lights in fact work fine, and the problem is above the wiring harness, and what you sent is not correct.

The package has been opened. You substituted my ordered part, it did not remedy the problem, I want a full refund, including S&H

Please advise/sent me Return Authorization, whatever your company policy is.

Thank you. Donna Turner