WOC54EC0AB04 Whirlpool Microwave - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Purchased 2 piece broiler pan from this site

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed in transit so your agent credited me with the cost of shipping.

When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.

All seems to be working well now.

Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?

IMPORTANT: DO NOT TOUCH THE REPLACEMENT LAMP WITHOUT WEARING CLEAN GLOVES. FILM OR FINGER PRINTS ON THE LAMP GLASS WILL CAUSE PREMATURE FAILURE OF THE LAMP.

Remove the 4 screws on right and left mounting rails that hold the unit to the kitchen cabinet.
Remove the oven door
Remove the chrome oven vent strip below the oven door. This allows a pry point beneath the combo microwave oven assembly to lift up the unit while pulling it out. (Assembly weighs 250 pounds)
Pull the unit out from the cabinet housing about 2-3 inches to reveal the right and left sides and the 4 screws holding the the control panel.
Remove the 4 control panel screws and pull off the face of the control panel
Remove the 2 harness connectors and the ground wire holding the control panel to the unit.
Unclip the circuit board above the lamp connector and slide it back out of the way. The lamp is now accessible.
Remove the lamp spring holding the lamp to the cabinet.
Remove the old lamp
Install the new lamp using clean gloves
Reassemble in reverse order.

REMOVED PANEL COVER [ 4 SCREWS]
UNSCREWED 2 SCREWS ON LATCH DOOR
ON THIS MODEL THE PART WAS IN TOO TIGHT OF QUARTERS SO I HAD TO LOOSEN A TOP PANEL SO I COULD RAISE PART HIGH
ENOUGH TO RELEASE IT FROM A CATCH AT THE BACK OF THE PART. PUSH PART BACK, RAISE AND PULL FORWARDS.
REMOVED 4 WIRES ONE AT A TIME AND ATTACHING TO NEW PART. REPLACED PART, TIGHTEN TOP PANEL AND REPLACED PANEL COVER.

NOT BAD FOR A 91 YEAR OLD

Should be about 1 5/8 inch with 3/8 inch prongs. Sent bulb won’t fit.
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I return the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961

Could not complete the repair due to broken part when arrived. Reached out to service department but have not heard back. Maybe email did not go through due to pictures attached of part condition once arrived.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

EASILY REMOVED GLASS COVER INSIDE OVEN AND REMOVED SMALL HALOGEN LIGHT BULB.
RECEIVED REPLACED WITHIN TWO DAYS OF ORDER AND REPLACED BULB AND GLASS COVER IN ABOUT 10 MINUTES.
MOST DIFFICULTY WAS HAVING TO BEND DOWN TO REACH INSIDE OF OVEN TO LOCATE POSITION TO INSERT BULB.

exact part in with the new out with the old

We had to remove screws from the vent covers above and below the microwave, then there were 2 screws (one on each side) that attached the microwave to the oven. Once all of the screws were removed we had to pull the microwave out. Then we pulled the light cord out, removed the burnt out light and installed the new one. Then reversed the steps.

Took off outer cover Popped out old bulb put in new one
Replaced cover

ordered new broiler pan