This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$53.85
In Stock
Order within the next 10 hrs and your part ships today!
This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tu...
$41.75
In Stock
Order within the next 10 hrs and your part ships today!
This door lock switch is a key component in compatible washing machines, designed to signal the control board when the door is securely closed. Once engaged, it enables the locking mechanism and allow...
$84.65
In Stock
Order within the next 10 hrs and your part ships today!
Having trouble with your LG appliance? It might be time to consider replacing the sensor assembly. This genuine OEM sensor assembly is designed and built to the highest standards by LG, allowing your ...
$85.75
In Stock
Order within the next 10 hrs and your part ships today!
Struggling with a less efficient washing machine? Our LG Washer Float Assembly could be just the solution you need. This authentic OEM part, specifically created for LG models, pushes moist air out of...
$30.75
In Stock
Order within the next 10 hrs and your part ships today!
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, th...
Looking to restore your LG washing machine to its peak performance? Our genuine OEM Ball Bearing could be just what you need! This part is designed with precision to support the spin basket shaft in y...
$64.85
In Stock
Order within the next 10 hrs and your part ships today!
Order within the next 10 hrs and your part ships today!
Questions And Answers for WM6700HBA
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Donovan
June 1, 2026
Trying to find replacement door gasket
For model number WM6700HBA
Hello Donovan, thank you for reaching out to us. According to our research, the door gasket, part number PS16879235, is compatible with your model number. We hope this information helps!
I need the front door boot for this front load washer
For model number WM6700HBA
Hello Phil, thank you for contacting us. The door boot seal for your model is part number PS16879235. If you require assistance to place an order, please contact customer service!
I am needing a replacement for the washer door magnet.
For model number WM6700H*A / WM5700H*A
Hello Marguerite, thank you for reaching out. The magnetic door plunger for your model is part number PS3618292. We hope this is what you were looking for!
Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that.
I removed the Wire and spring from the tub seal and then removed the seal on the side of the washer that contains the Door switch. I removed the two screws that held the door switch in place while holding the switch with my other hand. Once the screws where out I pulled the switch assembly out thru the gap and removed the wires from old assembly. I then plugged the wires into the new assembly aligned the holes up and put the screws back in the new door switch assembly. I then put the door seal and tub seal holder back on. This took about 15 minutes. I do recomend that you unplug the washer before starting this process.
Installed correctly but PartsSelect sent WRONG part, but part number on bag was correct. Installation of WRONG part fried the main board. A $100 fix is now costing me about $1300.00 for technician service and new unit. I asked PartsSelect to help with cost since outcome is due to their error. Totally unsatisfied. Will not suggest company to other DIYers.
