WM5000HVA (ASSEEUS) LG Washer - Overview
Sections of the WM5000HVA
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve - Hot
PartSelect #: PS3527427
Manufacturer #: 5220FR2006H
This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow ...
$67.05
In Stock
Water Inlet Valve - Cold
PartSelect #: PS11728995
Manufacturer #: 5220FR2075L
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$93.03
On Order
Washer Hose with Bellows
PartSelect #: PS3523347
Manufacturer #: 4738ER1004B
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$53.85
In Stock
Tub-to-Pump Drain Hose
PartSelect #: PS3523345
Manufacturer #: 4738ER1002A
This hose has bellows to allow for flexibility during the wash and spin cycles.
$39.55
In Stock
Washer Gasket
PartSelect #: PS3535219
Manufacturer #: MDS62058301
This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tu...
$41.75
In Stock
Pump Filter
PartSelect #: PS3522306
Manufacturer #: 383EER2001A
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your wa...
$34.22
In Stock
Washer Switch Assembly
PartSelect #: PS7792232
Manufacturer #: EBF61315802
This door lock switch is a key component in compatible washing machines, designed to signal the control board when the door is securely closed. Once engaged, it enables the locking mechanism and allow...
$84.65
In Stock
Washer Hose Connector
PartSelect #: PS3527289
Manufacturer #: 5214FR4006G
This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle...
$15.35
In Stock
Tub Bearing
PartSelect #: PS3522899
Manufacturer #: 4280FR4048N
This genuine washing machine tub bearing helps support the inner drum and allows it to rotate smoothly during wash and spin cycles. Designed to reduce friction and maintain proper drum alignment, it c...
$57.15
In Stock
Washer Float Assembly
PartSelect #: PS3579595
Manufacturer #: 4769ER4001B
Struggling with a less efficient washing machine? Our LG Washer Float Assembly could be just the solution you need. This authentic OEM part, specifically created for LG models, pushes moist air out of...
$30.75
In Stock
Common Symptoms of the WM5000HVA
[Viewing 7 of 7]Leaking
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
leaking tub-to-pump drain hose
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Parts Used:
-
Leslie from STOWE, VT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
52 of 76 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inlet valve leak
Followed directions on the video and went like a charm. Very impressed with service and video
Parts Used:
-
John from Northport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
34 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LE code appeared
From my research, I thought I needed to replace the Hall Sensor (also known as the Rotor Positioning Sensor). The Part Select site informed me that I might need to also replace the Rotor Assembly. The site said that I could not order just the Hall Sensor - I needed to order the Washer Motor Stator which would include the Hall Sensor. When I received the order, I found that the Motor Stator did not include the Hall Sensor. I found that I could order a part that matched the Hall Sensor I removed from my machine. I then ordered that part. I installed just the new Hall Sensor - the machine worked. I have returned the unused parts.
Parts Used:
-
Denise from LAKE PLACID, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
19 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!