The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$156.41
In Stock
Order within the next 10 hrs and your part ships today!
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$135.21
In Stock
Order within the next 10 hrs and your part ships today!
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$62.02
In Stock
Order within the next 10 hrs and your part ships today!
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
$10.25
In Stock
Order within the next 10 hrs and your part ships today!
This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can...
$50.01
In Stock
Order within the next 10 hrs and your part ships today!
Questions And Answers for WM3270CW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ray
September 17, 2023
WM3270CW ((ABWEVUS)) LG Washer
when I start cycle it fills with water and doesn't stop filling.It starts to tumble back and fourth but constantly keeps filling untill it get 3/4 full and stops . water starts to come out of door seal. I have to drain washing machine. CODE IE comes up. when I do The diagnostic check on components every thing works.
what could problem be?
For model number WM3270CW
Hello Ray, thank you for getting in touch. IE error code, which means it is experiencing an input error. The input in question is the inflow of water, which has failed to happen. Most likely, there is a failed water inlet valve, a problem with the incoming water supply or water hose, or a blocked inlet filter. Check the kinked or damaged inlet hoses. Check and be sure the hot and cold water supply valves are fully open. If this does not help, we recommend checking the pressure switch assembly, part number PS3529317. Good luck with your repair!
piece on bottom of door that is black and has a spring inside the small black cylinder. Looks like a piece is broke off that holds the part in the door
For model number WM3270CW
Hello Vicki, thank you for contacting us. The magnetic door plunger you are looking for is part number PS3618292. It holds the door open slightly when the washer is not in use, to allow the door and tub seal to dry, preventing mold and mildew. We hope this information helps!
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.