The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$160.58
In Stock
Order within the next 10 hrs and your part ships today!
This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow ...
$78.09
In Stock
Order within the next 10 hrs and your part ships today!
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$111.68
In Stock
Order within the next 10 hrs and your part ships today!
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$63.78
In Stock
Order within the next 10 hrs and your part ships today!
This washer sensor assembly, also known as a motor rotor position sensor, is a genuine OEM replacement part designed to monitor the direction and speed of the rotor during operation. By communicating ...
$80.21
In Stock
Order within the next 10 hrs and your part ships today!
The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will preve...
$78.50
In Stock
Order within the next 10 hrs and your part ships today!
This door boot seal is for front loading washing machines. This part forms a seal between the wash tub and the door, preventing leaks. We recommend unplugging the washer before installing this part an...
$234.78
In Stock
Order within the next 10 hrs and your part ships today!
If your washer isn’t filling properly or skipping parts of the cycle, this water valve might be the issue. It controls cold water flow for the bleach dispenser and prewash cycles. The valve connects w...
$172.14
In Stock
Order within the next 10 hrs and your part ships today!
Order within the next 10 hrs and your part ships today!
Questions And Answers for WM3050CW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kyle
February 4, 2024
Displays error code LE.
Tried reset by disconnect. Machine attempts to spin but will not make full rotation followed by grinding noise. I do not believe it to be drive belt. I will open to inspect, but if a common problem please provide a parts list and quote.
Thank you for your time.
For model number WM3050CW
Hello Kyle, thank you for getting in touch. According to our research, the error code LE indicates that the motor can not operate properly because of overload, or a foreign object is stuck in the tub. We would recommend checking the position sensor for continuity. If it is fine, then you will need to replace the rear tub bearing, part number PS3522899. Glad to be of help!
Hello Neal, thank you for your question! We have found that the size of your washer is almost 17.9 cubic feet. We hope this helps!
Was this helpful?
Thank you for voting!
Tom
February 28, 2023
Leaking at filter
For model number WM3050CW
Hi Tom, thank you for reaching out. According to our research, if water is leaking from the inlet valve filter, you may need to check the following parts: the hot water inlet valve, part number PS3527427, and the cold water inlet valve, part number PS11728995. Before replacing any of the parts, we would suggest checking the water supply connection to make sure it is not loose and cleaning the water inlet valve filters if they are clogged. We hope this sorts out your problem!
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replace the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
