WISR106DGBWW General Electric Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced broken START knob on dryer.
Slid off the old START knob, then pushed on the new START knob.
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
Parts Used:
-
SAM from ROCK HILL, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
502 of 513 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The inside of the Selector Knob was stripped
Removed the damaged knob and replaced it with the new knob. Very ease
Parts Used:
-
Frank from Irvine, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
383 of 389 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken drive belt
To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the legs in the middle, and approx. 4 to 6 on the bottom. This let me pull the bottom off partially to access the motor area. (I did did not take the bottom completely off, only about 2/3 off and let it bend over, as it was flexible tin) The belt was broken. After receiving the new belt, I positioned it between the pulley and the motor and between the drum and the big pulley. Then I rotated the big pulley, pulling the belt onto it as I rotated. At the same time, as I rotated, I pulled the other end of the belt on to the little pulley. Once it was on, I would put pressure on it as I turned the pulley, to jump the belt to the appropriate grooves on the little pulley. Note: the replacement belt had been modified, so it had one less groove than the pulley. I would have known this if I had read the insert that came with the belt first! Anyway, this was not a problem, only a design change. Also it was important to start the belt on the inside, so if it slipped, you didnt loose your bite. Total diagnostic, repair, and reassembly time: 30 minutes plus or minus. I had read other online forums that said you had to loosen the motor, etc. And I do know some type of a belt installation tool was offered on line, but I got along fine with my installation method. An extra set of hands would have been helpful, but not necessary.
Parts Used:
-
jon from barry, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
92 of 111 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blades broken off agitator
Simply put hands, one under each side of the agitaror and pulled up. The part snapped off very easily. I then placed the new part in the tub and pressed down. Extremely easy, should have done it sooner!
Parts Used:
-
Michael from Itasca, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
70 of 82 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing Machine would not balance on spin cycle
I replaced the work tub dampening strap because that what everyone recommended to replace for this problem. However the purpose of these straps is to dampen the agitation cycle and they have nothing to with the spin cycle at all. the balance ring assembly had been rubbing on the outer tub so I decided to replace it because of a "balance issue". However the ring is liquid with baffles to counter balance the load as it spins and it still had the liquid inside of it so it was actual not needed. What fixed my issue was I found a bolt laying at the bottom of the washer. This bolt was one of the 4 bolts that hold the outer tub to the metal support. When it feel out the tub was only held in at 3 points not the needed 4. This allowed it to rock a bit in the high speed spin and you thought it was going to fly into a 1000 pieces. I replaced the bolt and other parts since I had paid for them and everything works great now.
Parts Used:
-
Jarid from Louisville, KY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
58 of 80 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
selector knob cracked
ordered part on line--received in mail 2 days later--
just pushed on in 2 seconds--job done
how much easier can it get??????
just pushed on in 2 seconds--job done
how much easier can it get??????
Parts Used:
-
William from West End, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
74 of 136 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer over flows and floods floor
1. Noticed there was and obstruction in the air line that feeds the water level pressure switch. Cleaned out the air line but still had intermittent problem with flooding.
2. Evaluated the fill solenoid valve with meter and was functioning properly
2. Evaluated pressure level switch with meter and noticed that the switch was not changing state as it should when the water level is increasing. Replaced the level pressure switch, but still had problem.
4. Noticed the air line was damaged and had a hole that prevented pressure from building up. Replaced the air line and all is good!
2. Evaluated the fill solenoid valve with meter and was functioning properly
2. Evaluated pressure level switch with meter and noticed that the switch was not changing state as it should when the water level is increasing. Replaced the level pressure switch, but still had problem.
4. Noticed the air line was damaged and had a hole that prevented pressure from building up. Replaced the air line and all is good!
Parts Used:
-
Rick from Warrenton, MO
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
37 of 39 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitation and Spin not working.
I figured out that fuse link was open.Upon receipt of fuse link I ordered and replaced the bad fuse link hidden on wrapped electrical harness leading to the motor inverter board connector, BINGO... My washer works and I enjoy my washing machine again.My thanks and appreciation to partselect.com for the help & info you rendered to me.
Parts Used:
-
rodolfo from carpentersville, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
46 of 73 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
GE washer would not spin or agiate
Replaced inline fuse, simple fix.. but didn't work, checked lid panel switch which was working fine. Still no motor action, followed the reset procedure, and then watched above the motor for error lights, just below the drip cover, nothing, no error blinking code. Not sure why the kit contained two fuses, there is only one in our washer. So, my testing is over, in the error code, it stated if no blinking light, the failure is most likely a motor, I was hoping for something else, from switches to fuses. I reviewed the wiring diagram looking for an addition fuse link, found nothing.. The washer is four years old looks great, but now worthless, the replace motor for the unit is something like #300.00 with shipping. You can't test the motor, so it is a shot in the dark if you replace it. Really disappointed with GE's engineering and poor quality of manufacturing, and the lack of info to test the unit. We live on an Island, so not easy to find a local repair person. Your parts replacement service was fast and easy to use. But so much for GE washer.
Parts Used:
-
Frank from Vashon, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
42 of 62 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt.
Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while moving belt so it is properly seated on pulley.
Parts Used:
-
Mike from Meridian, ID
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
33 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer kept overflowing and flooding the garage every time we did a load of laundry
Instead of calling a repair man, we decided to look up the problem on the internet. We found that other people had the same problem on a website such as this. We narrowed it down to 2 parts. I opened up the panel on the washer where all the controls are (only 4 screws). Inside the panel was a diagram of the washer. We thought it would most likey be the Water level Pressure Switch. I found the part right away and removed it, I removed two connectors. It was really easy.
We ordered the part online and it came really quick (within two days). I installed the new part(Water level pressure switch) and tested it. The washer worked perfect and did not overflow. We tested it again with a load of laundry. Everything was good.
We saved a lot of time and money by fixing it ourselves. We did not have to wait around all day for a repair man and the part was under $30.00. I am happy the way it all turned out.
We ordered the part online and it came really quick (within two days). I installed the new part(Water level pressure switch) and tested it. The washer worked perfect and did not overflow. We tested it again with a load of laundry. Everything was good.
We saved a lot of time and money by fixing it ourselves. We did not have to wait around all day for a repair man and the part was under $30.00. I am happy the way it all turned out.
Parts Used:
-
Paul from Brea, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
33 of 40 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Support Tab
Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..ready to run.
Parts Used:
-
David from Rancho Cucamonga, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
30 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No hot water fill
- Troubleshot fill valve first. OK
- Followed leads to temperature selector switch.
- Checked resistance and live voltage at switch.
- Determined switch had failed on "hot" side.
1. SECURED POWER
2. Removed four torx screws on top of dashboard.
3. Removed six sheet metal screws from dashboard back.
4. Removed 4 leads from bad switch (one at a time).
5. Placed leads on new switch (one at a time).
6. Removed existing switch.
7. Installed new wired switch.
8. Re-installed dashboard back and top screws.
9. Op-test sat.
- Followed leads to temperature selector switch.
- Checked resistance and live voltage at switch.
- Determined switch had failed on "hot" side.
1. SECURED POWER
2. Removed four torx screws on top of dashboard.
3. Removed six sheet metal screws from dashboard back.
4. Removed 4 leads from bad switch (one at a time).
5. Placed leads on new switch (one at a time).
6. Removed existing switch.
7. Installed new wired switch.
8. Re-installed dashboard back and top screws.
9. Op-test sat.
Parts Used:
-
Richard from Kittery, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
26 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer drum would not spin, broken belt
I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)
Parts Used:
-
Eric from Bel air, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
20 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was not filling up larger than medium
Unplugged washer. Removed four screws on the top panel, unplugged and removed old water level pressure switch (which was visually broken), replaced with new part, put the top panel back on, re-connected power, and tested to make sure that the washer would now fill to Extra-Large. Worked!
Parts Used:
-
Joshua from Austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
17 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!