WHRE5550K2WW General Electric Washer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
DAMPENING STRAP 2PACK – Part Number: WH01X39337
No Longer Available
DAMPENING STRAP 2PACK
★★★★★
★★★★★
(9)
Part #WH01X39337
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
Tub Seal – Part Number: WH02X10383
$27.58
Special Order
Tub Seal
★★★★★
★★★★★
(4)
Part #WH02X10383
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qualified technician.
Tub Bearing – Part Number: WH2X1198
$47.16
Special Order
Tub Bearing
★★★★★
★★★★★
(4)
Part #WH2X1198
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. This bearing is made of metal, and is approximately 3 inches wide and 2 inches tall.
Tub Bearing Washer – Part Number: WH2X1197
$13.95
Special Order
Tub Bearing Washer
Part #WH2X1197
Split Ring – Part Number: WH02X10265
No Longer Available
Split Ring
Part #WH02X10265
This split ring is two inches in diameter.
Drain Hose – Part Number: WH41X10096
$79.66
Special Order
Drain Hose
★★★★★
★★★★★
(4)
Part #WH41X10096
This drain hose is a replacement part for your top-loading washer. The hose measures 57 inches in length.
Drain Pump and Motor Assembly – Part Number: WH23X10030
$137.13
Special Order
Drain Pump and Motor Assembly
★★★★★
★★★★★
(8)
Part #WH23X10030
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
6-Rib Drive Belt – Part Number: WH01X10302
$49.38
Special Order
6-Rib Drive Belt
★★★★★
★★★★★
(4)
Part #WH01X10302
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
Lid Switch with Wire Harness – Part Number: WH12X10334
$73.00
Special Order
Lid Switch with Wire Harness
★★★★★
★★★★★
(4)
Part #WH12X10334
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
Pump to Tub Inlet Drain Hose – Part Number: WH41X22935
No Longer Available
Pump to Tub Inlet Drain Hose
Part #WH41X22935
This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.
Socket Rod Support - White – Part Number: WH01X10001
$17.70
Special Order
Socket Rod Support - White
★★★★★
★★★★★
(1)
Part #WH01X10001
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the rod can prevent the tub from shaking too much during operation. If your washer is shaking excessively or emitting an odd sound during use, it may be because the rod support is broken, and the suspension rod is not able to do its job. This part is made of white plastic and is sold individually.
Shaft and Mode Shifter Assembly – Part Number: WH38X10017
$508.94
Special Order
Shaft and Mode Shifter Assembly
★★★★★
★★★★★
(2)
Part #WH38X10017
This essential washer component helps switch between washing and spinning modes by linking the motor to the wash plate. If your machine is stuck in one cycle, making grinding noises, or failing to agitate or spin properly, this part may need replacing. It’s designed to fit specific models and ensures smooth transitions between cycles. Installing a new assembly can resolve performance issues and get your washer back to working efficiently.

Manuals & Care Guides for WHRE5550K2WW

Click to download

Questions And Answers for WHRE5550K2WW

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Desmond - For model number WHRE5550K2WW
February 28, 2020
Drain but doesn't wash
Chris Boyle Profile
Hello Desmond, Thank you for the question. In order to trouble shoot this issue we will need a bit more details. When you say it will drain but not wash, is it going right to fill and then drain and skipping the wash cycle, or is the timer going through the wash cycle but the motor is not running to agitate and spin? When it drains, does it spin first or go right to drain? Any other details on the symptoms? Does the motor make any noise during the wash cycle? The more details the better since we can not be with the appliance. Please submit a new question if you have any follow ups. We are looking forward to hearing from you.
3 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Jeff - For model number WHRE5550K2WW
October 12, 2022
It is making a bad grinding sound, it doesn't want to go.
Chris Boyle Profile
Hello Jeff, thank you for your question. We have researched your model and found that the issue is probably with the tub bearing, part number PS271510. If that does not take care of the issue, then the problem is most likely to be related to the drive pulley, part number PS1482349, and/or the drive belt, part number PS1482278. If you require assistance placing an order, please contact customer service. We hope that helps!
$47.16
Special Order
Tub Bearing
$49.38
Special Order
6-Rib Drive Belt
$139.02
Special Order
Washer Drive Pulley
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Michelle - For model number WHRE5550K2WW
November 10, 2023
Agitator comes off during washing cycle. It still agitates but won’t stay attached to coupler..
Chris Boyle Profile
Hello Michelle, thank you for reaching out. Make sure the pulsator screw is properly tight. If it is fine, we would recommend replacing the coupling pulsator, part number PS2340064. We hope that helps!
$15.62
Special Order
Washer Coupling Pulsator
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Joe - For model number WHRE5550K2WW
October 7, 2021
Put a large blanket in washer and the gfci breaker tripped. Load never finished washing. Keeps tripping circuit. Could this be a bad motor? Could I please get the part number and price of a new motor. Could any other electrical parts be causing it to trip?
Chris Boyle Profile
Hello Joe, Thank you for the question. Tripping the Breaker is normally caused by a defective Lid Latch Switch. You can test the Switch for continuity while the Lid is closed. The Drive Motor is PartSelect Number: PS2577721. All prices are shown on our site. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
$73.00
Special Order
Lid Switch with Wire Harness
$585.22
Special Order
Drive Motor and Inverter Board Assembly
Was this helpful?
Thank you for voting!
Sonya - For model number WHRE5550K2WW
December 2, 2019
It won't agitate or spin, checked the belt and switch. Not sure what to do next
Chris Boyle Profile
Hello Sonya, thank you for writing. This is likely due to a faulty or damaged Tub Dampening Strap, part number PS271100 for your model washer. Good luck with your repair!
Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3

Common Symptoms of the WHRE5550K2WW

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine was not draining water from tub.
304 of 334 people found this instruction helpful.
  • Gerald from Midlothian, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)< br />2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.

NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
Was this helpful?
Thank you for voting!
washing machine would not go through all cycles or agitate
230 of 294 people found this instruction helpful.
  • Brian from Millerplace, NY
  • Easy
  • 15 - 30 mins
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
Was this helpful?
Thank you for voting!
machine would not drain all other functions seemed o.k
89 of 93 people found this instruction helpful.
  • douglas from danby, VT
  • Easy
  • 30 - 60 mins
  • Socket set
Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.
Was this helpful?
Thank you for voting!