Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature or amount of water needed.
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
This is the replacement tub baffle for your washer. It is made of black plastic and is approximately 13 inches by 2 inches. This part is sold individually and is an OEM part sourced directly from the ...
$81.05
In Stock
Questions And Answers for WFW8400TW03
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Charmaine
May 28, 2023
I need a motor control unit
For model number WFW8400TW03
Hi Charmaine, thank you for reaching out. The part you are looking for is the motor control board, part number PS11754006. We hope this helps!
Pf error during the following cycles heavy duty & sanitary machine stops. Cancel then machine drains. Problem occurs again with pf error message. Please do not request turning circuit breaker off and then on to resolve.
For model number WFW8400TW03
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
-During a power outage, if there was an unexpected amount of power supply line "noise" that the control detected as an incorrect voltage amount, the control could display the PF Error Code. Also, if any keys were pressed before the 10 second delay interval on power up, this could cause the PF Error Code to appear.
-If your dryer was installed recently (within approximately 3 months), contact a qualified electrician to verify the electrical supply.
Was this helpful?
Thank you for voting!
Louis
January 19, 2020
Thanks for responding but not answering my question. You requested both the washer and dryer part and serial numbers. The model number for the washer is wfw8400tw03 and serial number hly3501930. The model number for the dryer wed8300sw2 and serial number my3579751. For the 3rd time, the question is the same. A pf error occurs during the following cycles heavy-duty and sanitary for the washer. Push cancel and the washer drains. The problem occurs again every time during the heavy-duty and sanitary cycles. Lights in the house do not dim or flash. What is the minimum voltage that the pf error occurs? This must be a control board problem for the washer. Do not understand why you are asking for the model number and serial number for the dryer since the problem is with the washer.
For model number WFW8400TW03
Hello and thank you for writing.
PF error occurs if the voltage is less than 93 Volts AC. We do ask for the model and serial numbers as our system find information based on these numbers. It is possible that our system showed the unit initially as a combo unit, that would explain why we asked for both model and serial numbers. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
Louis
January 21, 2020
Ok, you answered the question on what supply voltage the pf error would occur. Thank you. Since it does not seem possible that the supply voltage ever was anywhere near 93 volts since the lights did not dim or flicker then the only conclusion must be a fault in the control board. Please confirm or indicate some other reason. Please provide how to replace the control board instructions and its cost. In addition provide names of local contractors in williamsburg va. Who could make repair.
For model number WFW8400TW03
Hello and thank you for writing.
There are 2 control boards in your unit that could cause the issue.
Control board PS11746709 and control board PS11755958, you would have to test both boards to establish which on is faulty, you could check for burn marks due to a short. Regretfully we do not have a list of contractors for your area. We hope this helps. Please contact us anytime if you require further assistance.
I need to level my washing machine, i am unable to find part i need to do it. Please advise the part number or picture. Of part.
For model number WFW8400TW03
Hello, Thank you for your question. You will want to check Leveling Leg with Foot Part #: PS11738005. That will be what levels your washer. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
