This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 7 hrs and your part ships today!
This temperature sensor detects the temperature within the oven cavity. This oven temperature sensor, for ranges, works together with the oven control board to measure and regulate the oven temperatur...
$120.73
In Stock
Order within the next 7 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.51
In Stock
Order within the next 7 hrs and your part ships today!
Order within the next 7 hrs and your part ships today!
Questions And Answers for WFG505M0BB2
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Russell
November 11, 2021
My oven is not lighting. The igniter is glowing. The burners are working. When the igniter is on I don't smell gas. Could it be a gas issue on the oven. I see that the gas lines split.
For model number WFG505M0BB2
Hello Russell, Thank you for the question. This could indicate a weak igniter. It can glow but not have enough power to open the valve. On a good igniter, there should be between 40 & 400 OHMS. A bad igniter will show no resistance or continuity. If the Igniter is good you can test the Valve. When testing the valve, it should be showing anything between 0 and 5 ohms of resistance. We hope this helps!
Grease or something got into the INNER OVEN DOOR WINDOW. Need to take apart and clean. Nothing in manual. AND a rubber seal around the whole door dimension, on stove side has come lose, afraid this is letting heat out of oven while using, can this be replaced, and why RUBBER when there is heat near it? Appears to be glued in place?
For model number WFG505M0BB2
Hello Trudy, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11756072 for the Heat Resistant Door Gasket. We have included a How to Video on replacing a Inner Oven Door Glass. It will show how to take the door apart so you can clean the glass. Thank you for your inquiry, good luck with this repair!
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.
The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees.
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.