SDSC150E4TTD (Type 1) DeVilbiss Compressor - Overview

This is a genuine replacement part manufactured for use with outdoor power equipment and air compressors. This nut is used to fasten various part assemblies on a range of different products. This nut is sold individually, please see model diagram for part usage and location.

This is an Genuine OEM replacement part used on Air Compressors. The gauge registers pressure readings and allows you to maintain needed pressure. This Gauge is Sold Individually. You would need a Wrench to secure this Gauge to the Manifold. When replacing this item make sure to unplug the air compressor and bleed out air from the tank.

This kit includes genuine OEM replacement parts and is compatible with various Porter Cable, DeVilbiss, and Black & Decker compressors. It includes eccentric bearing and screw. The bearing is sealed on both sides. The screw has a slotted hex-head.

When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where the drain valve comes in—it allows you to release the built-up water and keep your tank in good condition. Located at the bottom of the tank...Read more, this valve should be opened after each use to prevent corrosion and extend the life of your compressor. If you tend to leave air in the tank for long periods, water accumulation can be even more significant. This replacement drain valve features a thread size of 18 TPI and is sold individually. Regular maintenance with a working drain valve helps ensure safe and efficient compressor operation.

This replacement valve plate assembly is a high quality item designed for use on Craftsman air compressors. It is a genuine manufacturer sourced item that is used to control the airflow into the cylinder. Once the piston starts traveling up, the reeds on the valve plate open and air is sent into the air tank. Overtime the reeds will get w...Read moreorn eventually requiring valve plate replacement. One metal valve plate with reed valves and two rubber seals are included in this assembly. When replacing this valve plate assembly it is also a good time to replace the head gaskets which are sold separately. You will need a wrench set to complete this repair.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is a genuine OEM part. The Porter Cable nipple (1/4-18NPT X 1) is constructed of high-quality metal, and is compatible with many air compressors. This part secures the manifold to the compressor tank. An adjustable wrench set is helpful in making the repair. This part is sold individually.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

Restore air pressure in a compatible oil free air compressor with this cylinder service kit, it includes a cylinder sleeve, compression ring, piston rod screw, and two sealing rings, replace worn parts when the compressor runs but makes little or no air, unplug the compressor and release all tank pressure before repair, check the model and type number before ordering.