This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 11 hrs and your part ships today!
Glass ONLY. This inner door glass is a heat resistant part that fits into a stove, oven, wall oven, cooktop, or range as the inner glass panel of the appliance door.
$143.13
In Stock
Order within the next 11 hrs and your part ships today!
This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined...
$108.23
In Stock
Order within the next 11 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.51
In Stock
Order within the next 11 hrs and your part ships today!
This part is located at the bottom of the oven. This bake element is for ranges. The bake element is at the bottom of the oven and supplies the heat for baking. Unplug the range or shut off the house ...
$89.74
In Stock
Order within the next 11 hrs and your part ships today!
This part is the replacement door gasket for your oven. It is made of gray rubber and is sold individually. The door gasket runs along the circumference of the oven door and creates a seal that insula...
$40.94
In Stock
Order within the next 11 hrs and your part ships today!
This hinge is for a stainless steel door and is located on the left side of the oven door.
$69.70
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for RBS305PDB12
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Craig
November 29, 2019
Do you have video or repair instructions to replace the blower fan? Ours is humming, i.E. Motor or bearing noise. 14 yrs old, presume it makes economic sense to repair?
For model number RBS305PDB12
Hello Craig, thank you for writing! The replacement Blower Kit for this model is part number PS11742626. We do have a repair video for it; here is the link: https://www.youtube.com/watch?v=xRDPvAWwkrs. Good luck with your repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Philip
November 11, 2022
The cooling fan runs constantly and oven won't turn on, control panel does not work but clock runs but cannot be set. This happened after a short power failure.
For model number RBS305PDB12
Hello Philip, thank you for contacting us. We have researched your model and found that you may need to reset your oven. After resetting, check if the oven is working. If not, then the issue is probably with the limit thermostat, part number PS11747249. If that does not help, we recommend replacing the power terminal block, part number PS11745232. If you need help placing an order for it, reach out to our customer service. Glad to be of help!
Easily removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute project), and reattached the door to the oven. Cleaning the inside of the door took longer than the actual repair!
I removed the two screws that held the bake element in place. Next I removed the Bake Element. I had to unscrew the oven to go behind it because when one piece off of the element broke, it slide back behind the oven. I pushed the wire back thru the piece holes, connected the Element, and pushed the element with the wires back through the holes. I rescrewed the element in place and the oven. PartSelect helped me to save this year's Christmas.
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.