This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
This dishwasher water inlet valve is a genuine OEM component designed to regulate water flow into the appliance during the fill cycle. Typically located behind the lower kickplate panel in either fron...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
This is sold individually. Please order quantity required.
$8.82
In Stock
Questions And Answers for PLD2850RDC0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
April 15, 2023
I recently bought this home at foreclosure auction so I don't have any history on the appliance, unfortunately. On the normal wash cycle (haven't tried others) the dishwasher runs for about 10 minutes then gives the PF code. I'm wondering if it's a water temp issue. The water heater was not on so the incoming water is approx 70 degrees. When I open the dishwasher door the water is warmer so I know the dishwasher's heating element works. Anyway tips on troubleshooting? Thx.
For model number PLD2850RDC0
Hi Jim, thank you for reaching out. According to our research, the PF error code indicates a power failure and occurs when there is a 10% or more drop in power. We would suggest checking if the voltage going into the dishwasher is sufficient for it to operate. If it is sufficient, reset the dishwasher by turning off the power to the dishwasher for five minutes or by pressing the cancel button until the error clears. If the issue remains, the control board, part number PS2358675, might be faulty. Checking the control board for continuity using a multimeter might help. Good luck with your repair!
Cycle selection buttons quit working on several selections upper rack lower rack both racks
Still work on pots and pans crystal and no heat
Do you think this control panel or touchpad
For model number PLD2850RDC0
Hello Diane and thanks for writing.
This sounds more like the control panel # PS2358675 than the touchpad . You can also, refer to the manual troubleshooting section on our website for your model. We hope this helps. Please contact us anytime.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first place and messed up my subfloor and laminate flooring.
