All Installation Instructions for General Electric Range PGS950EEF4ES

Oven sensor was not holding temperature range.

Per the instructions included with part.

Parts Used:

Temperature Sensor Kit

CHARLA from NEW BRAUNFELS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

44 of 75 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Lamp Holder Burned

removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.

Parts Used:

Oven Light Housing

Jack from Okmulgee, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

23 of 28 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

defective temp. sensor

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

Parts Used:

Temperature Sensor Kit

Armand from COVENTRY, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

19 of 26 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

When baking at temps > 400 the oven would beep with an error code F5 and shut off

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

Parts Used:

Temperature Sensor Kit

Jack from Cypress, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

16 of 19 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven was not reaching or maintaining temperature.

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

Parts Used:

Temperature Sensor Kit

Raymond from Madrid, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

14 of 20 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom oven wouldn't warm up

Remove the door for easier access. Remove the fan cover from the back of the oven (about 6 Phillips head screws). Remove the bottom cover (2 5/16" screws). Lift the cover from the back and slide out. Remove the old igniter (2 5/16" screws). Pull the oven away from the wall. Remove back cover (3 5/16" screws). Unplug igniter, feed wiring through the oven. Install new igniter.

Parts Used:

Oven Burner Igniter

Mike from SAYREVILLE, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

13 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner would not light properly and flame uneven around the burner

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

Parts Used:

Burner Head - Large - 12K

Bret from South Haven, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven light did not work

Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.

Parts Used:

Oven Light Housing

Howard from Rio Vista, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

9 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wire connection to socket was bad

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

Parts Used:

Oven Light Housing

David from Gansevoort, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt burner

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Parts Used:

Burner Head - Medium - 9500

Janine from Wind Gap, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed To Replace Burner

Took longer to open the box.

Parts Used:

Small Burner - 5K

Robert K from York, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

Parts Used:

Oven Light Housing