P2S975SER2SS General Electric Range - Instructions

Per the instructions included with part.

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

Removed screws using nut driver. Pulled element way forward until wires came through. Pondered how to detach burned out element from wires. Chickened out, call neighbor who grasped things firmly with two hands and pulled. Old element came loose. Popped in new element. Cursed the screws that wouldn't align with holes to support element; finally did it. Screwed element plate in place. Put oven door back on, plugged it in and turned it on hoping that we hadn't reversed the wires. Job accomplished.

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

Here's how I fixed my problem.
I took the aluminum cover, the part that sits over the jet & the igniter, which simply comes off. It's the part that the igniter discharges to. I took this cover off & using a pencil I scratched the lead of the pencil into the area
which is around the igniter. I made sure to cover the area with as much lead as I could get on it. You need to make sure that you do this to all four burners. The only care you need to take, is not to block the gas jet which is in the igniter recess. It's been about 3 weeks since I added this & the burners click loudly & have lit without a problem. It appears that the aluminum may develop a coating on it of some kind which is highly resistive.

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

After turning the power off to the range, it was as simple as removing the screws for the broiler itself and the bracket and plugging in the new element. Yes, it was that easy.

The broiler uses two male slip-on connectors that attach to two wires with female connectors in the stove. When removing the broiler element, I discovered that one of the two wires was burned in half specifically where the wire crimped to the female connector. This is abnormal and raised some concern. However, I deduced that the terminal crimp from the factory must have been defective and the wire nicked or cut in order to produce enough heat at that point for the wire to burn and fail. The female crimp terminal is a special, solid right angle design that I was unable to locate locally even at an electrical wholesale distributor. A straight terminal connector was used and crimped after stripping a new section of the wire. Heat will melt solder. You must use a high quality crimp connector and tool. The connector was then very carefully angled down slightly to maintain a safe distance from the back shield of the stove to the wire when in place. The new broiler works fine. There was likely nothing wrong with the old one. Just a wiring issue.

After I ordered a new element unit, I read the "do it yourself" review on the page. I took the back off of the range and found the broken wire. I found that I had the same problem with the wiring, and that maybe the element was not the problem. I went to Lowe's and purchased a female spade connector, because no one would sell me one through the parts department. All I did was cut off the wire at the end of the burned section, stripped back about 1/2 inch of the wire and put on the new spade connector. I took off the origonal connector/crimp, and slipped on the new one. (You do have to make sure that the wiring doesn't touch the range back) The element was not the problem, so the origonal one still works fine. I may keep the element I ordered, just to have it if this one goes out. I didn't even need to remove the screws from the element inside the oven. It can all be done from the back of the range.

Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.

New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.

Turned off electricity. Removed two screws that held the element in back of oven. Removed the two screws that held it up to top of oven. Disconnected the two wires that held it in the rear of the oven. Removed it from the top support. Replaced the old element with the new in the support. plugged it it, replaced all four screws. Turned on the electricity and turned on the oven-it worked!

Don't forget to unplug and/or turn off the main breaker!

removed 2 1/4in. drill screws holding broiler element to oven removed 2 1/4in.drill screws holding broiler element to top of oven removed female spade connectors ffom old element and reversed assembley very easy