The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt att...
This 240V/5400W heating element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current, causing the wire to heat up. The heat ...
This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.
This dryer drum roller kit is designed to restore smooth and quiet operation in a wide range of dryer models. It includes two drum rollers, four tri-rings, and one to two retaining washers, providing ...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This high-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Fahrenheit, this piece will shu...
This manufacturer-certified dryer lint filter is used to collect lint during the dryer cycle, to prevent damage to the machine and to prevent lint from sticking to clothes. This model comes in white a...
If your dryer drum isn’t spinning, the motor might be the issue. This replacement motor works with many Whirlpool-brand dryers made before 1996 and comes with the pulley already attached. It powers th...
$143.77
In Stock
Questions And Answers for NED4600YQ0
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Adam
December 31, 2019
Yes do you carry a Amana dryer repair kit. Belt pulley ect dont need the motor
For model number NED4600YQ0
Hello Adam,
Thank you for your question. The maintenance kit for your model is under part PS373087. We hope this helps!
The side is not working, so on manual side not drying as it should
What could be wrong.
For model number NED4600YQ0
Hi Charles, thank you for reaching out. Based on the description that you have provided, we would recommend checking the following parts: cycling thermostat, part number PS11741405, high limit thermostat, part number PS11742185, dryer blower wheel, part number PS11743785, drive belt, part number PS346995, and door gasket, part number PS11731610. We hope this sorts out your problem!
Seems the dryer enters cool down mode too soon. Have to turn the dial back to 60 minutes and then it will finish drying the clothes. Have cleaned the ductwork and it improved some but it really wasn’t too bad. Looked inside for obvious moisture sensors but didn’t see any.
For model number NED4600YQ0
Hi Beth, thank you for reaching out. Check the cycling thermostat to ensure it's working correctly. If it's faulty, the dryer may not be able to regulate its temperature properly, leading to premature cool down. Its part number is PS11741405. We hope this solves your problem!
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element with an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off.
The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.
