N89RH17-1 (Type 0) Bostitch Nailer - Overview

Diagrams for N89RH17-1

See every part. Know exactly what you need.

Exploded Diagram A

Parts for the N89RH17-1

$7.44

WASHER-RUBBER-7

Part #854004

This rubber replacement seal is designed for use with select pneumatic and coil-fed nailers, providing a tight and reliable seal at the nose of the tool. Its primary function is to prevent air leakage during operation, helping to maintain consistent pressure and performance. Over time, seals can wear down or become damaged, which may lead...Read more

Read less

$7.44

Lube (2cc)

Part #9R206705

This genuine manufacturer-approved lube which is specially made for use with power tools. It helps to lubricate the system allowing for easy movement and protecting parts from usual wear. Please make sure to refer to the owners manual of your model for the correct application of this lube. Keep in mind this high-quality tube is sold individually.

$7.44

PIN-CHECK PAWL

Part #149882

Genuine Bostitch replacement part, this item is sold individually. The purpose of the Pawl Check Pin is to secure the part number 16042 Check Pawl in place. The part number N12112 Hinge Pin Retainer holds the Pawl Check Pin in place.

$7.44

PIN-SPIRAL M3X30

Part #100298

It is a genuine manufacturer-supplied component which is made for Bostitch nailers and staplers. This is a special spiral pin that is utilized to secure the trigger. It is an identical replacement for a faulty or a missing hardware that was installed on a new unit. To ensure the proper repair procedure, refer to the appropriate diagram fo...Read more

Read less

$7.44

O-RING-.056X.060 NBR

Part #166797

The o-ring is an authentic OEM sourced item which is specially produced for use with Bostitch nailers. A set of pliers might be necessary during the installation of this part. It may become broken or lost and will need to be replaced. This is made of rubber and is available as an individual replacement part.

$7.44

SCREW-SHCS-M4X0.70X2

Part #121052

The metal screw attaches to the trip cover. This is a genuine Bostitch part sourced directly from the manufacturer for use in nailers and staplers. This item is available as an individual replacement. It may require an allen wrench during installation. It will need replacing if it becomes broken or stripped.

$7.44

SPRING-COMPRESSION

Part #100387

This compression spring is an OEM direct from Bostitch. The metal spring is compatible with many stapler and nailer tools. This item is fitted within the trigger valve kit of the device. The spring is the mechanism for the trigger to move back in place. Although this part is sold individually, it can also be found in the SEQ6 Kit. A small hammer and a hex key are helpful in the repair.

$7.44

PIN-SPECIAL

Part #121407

This part is available as an individual replacement. The special pin attaches to the magazine and is made of metal. A set of pliers might be helpful during the installation of this item. It will need to be replaced if it becomes broken. This is a genuine OEM sourced part which is specially designed for use with Bostitch nailers.

LABEL-SENSOR SMALL (

Part #120927

$7.44

SCREW-SBHCS-M6X1.00X

Part #MSB6100-12

This is an authentic Bostitch replacement part that has been sourced from the original manufacturer to be used with pneumatic nailers. The metal screw is used with several different types of fasteners and the application of the screw can vary based on the model of the nailer. The screw is sold as an individual replacement part.

$61.75

LOCTITE

Part #851385

$7.44

SCREW-SHCS-M4X0.7X16

Part #MSC4070-16

This replacement screw is a high quality item that has multiple uses depending on the model of your tool, please make sure to check appropriate diagrams for correct location and use of this hardware. It is a genuine screw that is sourced directly from original equipment manufacturer for use with nailers and staplers. Note this durable metal hex socket head screw is included per order.

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

would not fire nails

10 of 15 people found this instruction helpful.

Richard from Bogalusa, LA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers

remove 2 Philips head screws, drive out drift pins with drill bit. Remove TVA6 replace with new TVA6 making sure TVA6 is completely seated and slots are aligned with drift pin holes! Drive in drift pins. Replace trigger and screws.
This did not solve the problem as suggested by Parts select.
Replaced Head Valve Seal...Problem re ... Read more

Read less

Was this helpful?