This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time
$190.78
In Stock
Questions And Answers for MVWX550XW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
November 1, 2021
How to replace a Maytag washer cold water valve
For model number MVWX550XW1
Hello James, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS12348073. There is a How to Video listed with the part on how to install. We hope this helps!
Problem, lid strike inoperable, white, round, catch centered, needs replacing.
I have not found a replacement, nor a video showing how to remove and replace once found. HELP.
For model number MVWX550XW1
Hello Shirley, thank you for contacting us. The lid strike, part number PS11750882, and lid lock bezel, part number PS11754116, fit your model. The attached video can help you install the lid latch strike. For installing the lid lock bezel, follow these instructions. To replace the lid lock bezel, it needs to be freed from the underside of the washer top assembly. Unscrew the hinges on the back of the washer control panel. Unscrew the nut to remove a small metal plate behind the control panel. Now remove the washer top assembly, by pulling it forward. Slightly push the top assembly up and push it back to unlock the washer's top. On the underside of the washer's top assembly, unscrew the two nuts securing the lid lock bezel. Now you can easily remove and replace the lid lock bezel. We hope this information helps!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.