This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
The drain hose carries used water from the washer to your house drain.
$31.80
In Stock
Questions And Answers for MVWX500BW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pete
February 6, 2020
What torque setting should be used for the drive pulley (attached to the basket) to be tighten to?
For model number MVWX500BW0
Hello Pete, thank you for your question. There is no torque setting for the pulley, per our installation video. In the video it shows the bolt being tightened about 3/4 of a turn after some resistance is felt. You can see the video at this link.
https://www.partselect.com/PS10057144-Whirlpool-W10721967-Washer-Drive-Pulley.htm?SourceCode=4&SearchTerm=MVWX500BW0&ModelNum=MVWX500BW0
2 people found this helpful.
Was this helpful?
Thank you for voting!
Janet
May 15, 2023
I need a new paddle that pushes in the fabric softener. Mine came loose and was misplaced before it could be repaired.
For model number MVWX500BW0
Hello Janet, thank you for the query. According to our research, the paddle does not come separately. You may need to replace the complete drawer, part number PS11757010. We hope this helps!
Machine works fine but does not stop at the end of the cycle. It will go to the end of the cycle and the done light will come on. When the done light goes out, the lid lock and the sensing lights come on and stay on. What can be done to fix this problem? By holding the start button for several seconds the both lights will go out and the machine will be back to normal.
For model number MVWX500BW0
Hello Elmer, Thank you for the question. This could be an issue with a defective Control Board, PartSelect Number PS12070898. Hope this helps!
Leaks drips of water in tub after use sometimes will have 2-3 inches of water
For model number MVWX500BW0
Hello Teresa, thank you for reaching out. According to our research, we would recommend checking the water inlet valve, part number PS11756681, to fix the issue. We hope this solves your problem!
I noticed a lot of oil when replacing the actuator. Where is it coming from?
For model number MVWX500BW0
Hello Jessie, Thank you for the question. Normally the Oil would come from the Gearcase. If there is oil in or under the Tub you may have a worn Tub Seal. We hope this helps!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.