This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing mach...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Ask our experts a question about this model and we'll get back to you as soon as possible!
27 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
JOHN
March 31, 2022
My washing machine sounds like a Jet when spin dry?????
For model number MVWB835DW4
Hi John,
Thank you for your question. If the washer sounds like a jet during the spin cycle, the noise is coming from the bearing that is pressed up against the outer tub. It is likely worn and will need to be replaced. The bearing is sold with the gearcase. The part number listed under your model number for the gearcase is PS16220921. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Wash plate will not come off after the wash plate screw is removed. What am I missing?
For model number MVWB835DW4
Hello Joseph, Thank you for the question. Over time the Plate can become "stuck" from build up and use. It may take a bit of force. Steve gives some tips in the How to Video for this Washplate. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
My washer is leaking from the bottom. It appears to be coming from the center of the machine, and i can see water spray all along the inside of the shell.
For model number MVWB835DW4
Hi Joe, thank you for reaching out. Based on our understanding of the issue, we would suggest you check the tub seal attached to the gearcase shaft, and the washer, part number PS11770333. Also, make sure that the different parts of the washer at the center are tightly installed. We hope this sorts out your problem!
Drum jiggles then can hear lid lock followed by musical notes and f5 appearing then all lights off.
For model number MVWB835DW4
Hi Jim,
Thank you for your question. The F5 error code is letting you know that the lid cannot lock. Check the lid to see if there is anything preventing it from closing. If there is remove it. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Cannot rid odor of stagnated water - would like to be able to clean it out. How do I reach the area under the drum or the filter if there is one, that might trap debris.? Any suggestion?
For model number MVWB835DW4
Hello Virginia, thank you for contacting us. There are no filters in this model. You can remove the wash plate to see if there is any stagnant water and clean the area. Here is a video to help you remove it. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate ( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Raised lid to remove two Torx head screws from each hinge. Lid will then lift off of hinges. Installation of new lid was the reverse of the removal procedure. It is best to install one hinge to the lid by removing that hinge from the washer. The lid can then be installed by inserting that hinge into it's spot and then over the other hinge. Install the hinge screws into the second hinge and the job is complete. The lid now closes properly allowing the automatic lid lock to function properly.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
