MV1746AD (CBKELGA) LG Microwave - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave Grease Filter – Part Number: 5230W1A012E
$21.95
In Stock
Light Bulb - 120V 30W – Part Number: 6912W1Z004B
$24.95
In Stock
Air Duct Bracket – Part Number: 4810W1A151A
$24.15
In Stock
Air Duct Bracket
★★★★★
★★★★★
(1)
Part #4810W1A151A
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, and replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
Microwave Damper – Part Number: 4900W1A001B
$17.55
In Stock
Microwave Damper
★★★★★
★★★★★
(2)
Part #4900W1A001B
This metal vent damper door closes off the exhaust duct when the fan is not running to stop outside air from entering the microwave unit, and opens when the fan turns on to allow air to vent away from the microwave. This vent damper door measures approximately 10 inches long x 3 inches wide and fits LG microwaves.
Charcoal Filter – Part Number: 5230W1A011B
$28.55
On Order
Charcoal Filter
★★★★★
★★★★★
(1)
Part #5230W1A011B
This is the replacement charcoal filter for your microwave. It is approximately 8 inches by 5 inches. The charcoal filter removes cooking odors from the air that circulate through the microwave vent. You will likely need to replace the charcoal filter if you notice any damage to it, or if it has been in your microwave for a long time. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Time Delay Fuse – Part Number: 3B74133Q
$13.15
In Stock
Time Delay Fuse
★★★★★
★★★★★
(1)
Part #3B74133Q
Sold individually.
Mounting Plate – Part Number: 3300W0A045A
$40.32
In Stock
Mounting Plate
Part #3300W0A045A
This mounting plate is a manufacturer-approved replacement part for your microwave. The mounting plate, or bracket, secures your above-range microwave in place against the wall. To conduct this repair, make sure to first disconnect the power source, and wear protective gloves.
Charcoal Filter – Part Number: 5230W1A011E
$28.95
In Stock
Charcoal Filter
★★★★★
★★★★★
(1)
Part #5230W1A011E
This is the replacement charcoal filter for your microwave. It is approximately 8 inches by 5 inches. The charcoal filter removes cooking odors from the air that circulate through the microwave vent. You will likely need to replace the charcoal filter if you notice any damage to it, or if it has been in your microwave for a long time. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Spring – Part Number: 4970WRA001G
$13.15
In Stock
Spring
★★★★★
★★★★★
(1)
Part #4970WRA001G
This spring provides tension or controlled movement within the appliance mechanism. Engineered for durability, it supports smooth operation and helps maintain proper alignment of connected components.
Microwave Micro Switch – Part Number: 6600W1K001C
$20.85
Special Order
Microwave Micro Switch
Part #6600W1K001C
Microwave Motor Ac Synchronous – Part Number: 6549W1S013H
$50.55
In Stock
Microwave Motor Ac Synchronous
★★★★★
★★★★★
(4)
Part #6549W1S013H
If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed through the bottom. The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is making a grinding noise it will need to be replaced. If the motor does not turn, you can check for voltage or continuity with a multi-meter. Make sure the power is disconnected from your microwave before beginning this repair.
Rivet – Part Number: 4051W3A001A
$11.95
In Stock
Rivet
Part #4051W3A001A

Common Symptoms of the MV1746AD

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave would not rotate or heat up food.
52 of 77 people found this instruction helpful.
  • Joshua from WHITE LAKE, MI
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
After watching a few youtube videos, I used a phillips SD to take controll pannel off to access the switches that sense when microwave door is closed. Swapped out all 3 switched and mocrowave works like new. $20 fix (shipping included)
Was this helpful?
Thank you for voting!
Broken door micro switch. (unit does not start heating)
37 of 68 people found this instruction helpful.
  • JAMES from BILLINGS, MT
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far l eft side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.
Was this helpful?
Thank you for voting!
needed grease filters for a used over range microwave
26 of 58 people found this instruction helpful.
  • tony from kewanna, IN
  • Really Easy
  • Less than 15 mins
ordered on the part select web site, came quickly, order was correct
Was this helpful?
Thank you for voting!