This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
At 91-5/8 inches in length, this dryer drum belt from Maytag has five ridges. It is all black in color and is made entirely of rubber. This flat belt is 3/8 of an inch wide.
This is a rectangle shaped lint filter screen used for some gas and electric clothes dryers. The dimensions of this lint filter screen are approximately twelve and a half inches long by seven and thre...
Also known as the door boot seal. This part includes the drain and plug. The seal is located around the door of the washer to prevent water from leaking.
This kit comes with grease, earlier lip seal, revised lip seal, o-ring, seal tool, and washer kit.
Used primarily on front load washers.
NOTE: Bearing is NOT sold separately. It is only available ...
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
$17.15
In Stock
Questions And Answers for MLE2000AZW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Regina
June 27, 2021
I need a door boot seal for my 2000 Maytag front loading washing machine as it is very moldy. Is there any other type that I can use for it instead.
For model number MLE2000AZW
Hello Regina, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS2003890. We looked up the part and it is listed as No Longer Available/Discontinued sorry. There are no part substitutions listed. Our suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers and contact us back with he updated substitution number. We hope this helps!
I am concerned about the amount of water I can hear under the drum once a load of laundry is complete. There is no water left in the drum but a large amount can be heard when I try to turn the empty drum. There are no kinks in the discharge hose or blockages. Is there anything I can do?
For model number MLE2000AZW
Hi Kathryn, thank you for reaching out. There is always a little water under your washing machine drum after doing laundry. This is because after the washing machine pump pumps out water, there is always some water left in the drain line which falls back into the tub and levels out.
If there is a high level of water, ensure that the drain hose is properly installed. It should be elevated at a certain point and securely placed into a drain or standpipe. If the drain hose is placed too low or too deep into the drain, it can create a siphoning effect, where water is continuously drained out and then refilled, causing water to remain in the drum. Check the door seal (gasket) and the drum for any visible damage or wear. If the seal is damaged or has gaps, it could allow water to enter and remain in the drum. If you find any issues with the seal, consider replacing it. If this does not help, we recommend replacing the lip seal kit, part number PS2003500. We hope this solves your problem!
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job. Thank you.
