MHWE200XW00 Maytag Washer - Overview
Sections of the MHWE200XW00
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Front Load Washer Bellow Door Boot Seal - Gray
PartSelect #: PS11753988
Manufacturer #: WPW10381562
This is the main seal between the front bulkhead and the outer tub. If the washer is leaking, the door boot may have a tear in it. Overloading the washer is the most common cause for a torn door boot
$172.15
In Stock
Washer Drain Pump
PartSelect #: PS11757304
Manufacturer #: WPW10730972
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. It has two ports for water to pass through: a large one, and a s...
$181.12
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$15.95
In Stock
Door Strike/Hook
PartSelect #: PS11746261
Manufacturer #: WP8540221
Used to help make the door stay closed. Sold individually.
$15.45
In Stock
Shock Absorber
PartSelect #: PS11723173
Manufacturer #: W10822553
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
$81.40
In Stock
Stacking Kit
PartSelect #: PS990537
Manufacturer #: 8572546
This kit allows you to stack your washer and dryer to maximize your laundry space.
$61.07
In Stock
HOSE
PartSelect #: PS12723931
Manufacturer #: W11366249
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
$45.31
In Stock
Washer Dispenser Hose
PartSelect #: PS12723930
Manufacturer #: W11366227
This dispenser hose is for washers and carries the contents of the dispenser drawer to the washer tub.
$37.95
In Stock
Dual Cold Water Valve
PartSelect #: PS11750469
Manufacturer #: WPW10212596
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW...
$89.98
In Stock
Washer Door Lock Latch
PartSelect #: PS11751211
Manufacturer #: WPW10253483
If your washer door won’t close or lock, or your machine won’t start, this door latch might be the issue. It’s the part that keeps the door shut tight during the cycle and makes sure everything runs s...
$215.95
In Stock
Bellow To Tub Clamp
PartSelect #: PS11746259
Manufacturer #: WP8540108
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
$36.15
In Stock
Washer Temperature Sensor
PartSelect #: PS11755214
Manufacturer #: WPW10467289
This part regulates the temperature of the water in the tub. The sensor is located in the heating element.
$47.33
In Stock
Questions And Answers for MHWE200XW00
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry
February 3, 2020
Leaking in front of washer
For model number MHWE200XW00
Hello and thank you for writing.
It certainly sounds like it could be a damaged bellow boot seal PS11753988 you should check the part(s) for signs of damage and replace the part(s) as needed. It is recommended to change the clamp PS11746259 for the seal at the same time We hope this helps. Please contact us anytime if you require further assistance.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Bellow To Tub Clamp
$36.15
In Stock
Front Load Washer Bellow Door Boot Seal - Gray
$172.15
In Stock
Derek
February 23, 2020
Wont fill with water and begin wash cycle also door locks as normal when u start cycle but will not unlock
For model number MHWE200XW00
Hello, Thank you for your question. You will want to check into the door lock then. If it is not functioning normally you will need to replace it. We hope this helps, good luck with this repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Charlie
June 16, 2025
When push the power button it won't come on. What part do I need?
For model number MHWE200XW00
Hi Charlie, thank you for the question. Ensure that the power cord is properly plugged in. If it is fine, the issue could be with the control board, part number PS11750475. You may need to replace it to fix the issue. We hope this sorts out your problem!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Control, Electric
$359.72
Special Order
Magnus
August 15, 2023
Washer machine fills with water when turned off overnight. Other sources say needs new water valve but i cannot seem to find that part on this site.
For model number MHWE200XW00
Hello Magnus, thank you for the question. The compatible water inlet valve for your model is PS11750469. We hope this information helps!
Was this helpful?
Thank you for voting!
Related Parts:
Dual Cold Water Valve
$89.98
In Stock
Asma
December 6, 2023
Hi, I am looking for door seal for this model. The seal the goes on the cell of the washing machine and has a rubber ring. Gasket?
For model number MHWE200XW00
Hi Asma, thank you for your inquiry. The seal that you are looking for is door boot, part number PS11753988. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
Front Load Washer Bellow Door Boot Seal - Gray
$172.15
In Stock
- < Prev
- 1
- 2
- Next >
Common Symptoms of the MHWE200XW00
[Viewing 14 of 14]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Engine runs but does not pump water
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
F 21 error
Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Parts Used:
-
Andrew from St.Louis, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
376 of 424 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch module was defective
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.
Parts Used:
-
Carlton from Greer, SC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
103 of 123 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water pump failed
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
Parts Used:
-
Kurt from Caliente, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
98 of 110 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!