This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$14.96
In Stock
Order within the next 11 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.51
In Stock
Order within the next 11 hrs and your part ships today!
This is a replacement screw and washer for your oven/range. It is a Phillips-head screw approximately half an inch long, and the washer is approximately 1 inch in diameter. The screw attaches the oven...
$10.14
In Stock
Order within the next 11 hrs and your part ships today!
Order within the next 11 hrs and your part ships today!
Questions And Answers for MGR5751BDW
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeff
February 24, 2020
Auto clean locking doesn't lock - what do i do
For model number MGR5751BDW
Good Day Jeff. Thank you for your question in regards to your unit (Model Number MGR5751BDW). Based on our research, this may be the result of your unit having been accidentally been set to "Sabbath Mode". For more information on this, we recommend reaching page 15 of your unit's owner's manual. If you do not have a copy of your unit's owner's manual it can be found at the following URL: https://www.manualslib.com/products/Maytag-Mgr5751bdw-604678.html. We also recommend reviewing the Troubleshooting Guide in the Owner's Manual as it has a lot of tips that should be able to help you to solve the issue you are having. We hope this helps! Best Regards.
Was this helpful?
Thank you for voting!
Patrick
July 7, 2021
Oven takes for ever to get to setpoint. Just started to happen. Took 20 minutes to get to 350 deg f, 40 minutes to get to 375 deg f. Takes longer than normal to light burner, burner ribbon does light fully, but i don't hear the burner staging up or cycling like it use to.Serial # 15565716ng
thanks, pat garman
For model number MGR5751BDW
Hi Patrick,
Thank you for your question. If the oven is not heating correctly, the issue is likely the temperature sensor. This part fixes the issue the majority of the time. If the sensor is fine, you will need to check the electronic control board and the wiring between the parts. We hope this helps! Good luck with the repair!
my oven is at least 16+ years old and takes about four hours to preheat, is the culprit a faulty igniter?
For model number MGR5751BDW
Hello Jenard, thank you for reaching out. Based on the description that you have provided, we would recommend replacing the oven igniter, part number PS2085070, to fix the issue. We hope this solves your problem!
sorry i left out this last detail from my previous email, the oven also has difficulty maintaining a set temperature immediately after preheating and will occasionally drop 10-15 degrees. afterwards it takes roughly 30 additional minutes to maintain a set temperature.
For model number MGR5751BDW
Hello Jenard, thank you for reaching out. Based on our understanding of the issue, we would suggest you replace the oven sensor, part number PS2003225, to fix the issue. We hope this is what you were looking for!
My oven has two igniters so I needed to determine which one was the problem.
Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Range")
