This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
$28.93
In Stock
Order within the next 11 hrs and your part ships today!
This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them ...
$39.39
In Stock
Order within the next 11 hrs and your part ships today!
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$17.11
In Stock
Order within the next 11 hrs and your part ships today!
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 11 hrs and your part ships today!
This manufacturer-certified dryer lint filter is used to collect lint during the dryer cycle, to prevent damage to the machine and to prevent lint from sticking to clothes. This model comes in white a...
$59.29
In Stock
Order within the next 11 hrs and your part ships today!
This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.
$20.81
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for MGDC465HW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
March 29, 2023
dyer does not get warm or hot
For model number MGDC465HW1
Hello Mike, thank you for contacting us. Based on our research, we would recommend checking the following parts: thermal fuse, part number PS11741460, M series coil kit, part number PS334310, igniter kit, part number PS334180, radiant flame sensor, part number PS11741429, and thermostat, part number PS11745959. We hope this solves your problem!
Hello Valorie, thank you for reaching out. The compatible door catch for your model is part number PS12745673. It helps keep the door latched properly. If you require assistance to place an order, please contact customer service!
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils. Not knowing what the problem was I started looking at the coils and could not see any broken parts. So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading. I replaced with a new one and put it all back together the way I took it apart. Then I plugged it in and it worked first time, I now have warm dry clothes.
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.
Ascertaining the problem was the most time consuming part.
The actual repair was quite simple and didn't take but 15-20 minutes.
First removed front and drum to check gas valve and igniter. No gas, no ignition. Checked power to devices; none (check hot line to ground, not to neutral.). Removed back of control panel looking for a relay or something. Found none, but did find a wiring diagram. That is where the site really came in handy. Studied wiring diagram together with the exploded view and pictures of each part to come up with a troubleshooting plan. Took the back off as well as a cover inside. Tested each part with meter, again going to ground and not across the device. Of course, the final device before the gas valve, a one time thermal fuse, was the bad part. At first assumed just a bad part. Later wondered if fuse did it's job and another part was bad. Ordered and installed new thermostat just in case. Put everything together after a complete cleaning and everything is fine so far. Not a particularly hard job because I had the wiring diagram and access to parts select site. Would have been much harder without them. Took a long time because almost the entire dryer had to come apart. But it got a good cleaning because of it and found a couple of bucks in change to help offset the cost. Can't imagine what a service call would have cost.
