This water filter purifies water going to the water dispenser and sometimes the icemaker as well. This part should be replaced if it is causing reduced water flow or just replaced periodically per the...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This drawer slide rail cover is for refrigerators.
Drawer slide rail cover is a decorative trim that covers the slide rail.
Wear work gloves to protect your hands when installing this part.
Sold individually. Crisper drawer is an original equipment manufacturer (OEM) part that fits some bottom-freezer Kenmore, Amana, Crosley, Jenn-Air, KitchenAid, Maytag and Whirlpool refrigerators.
T...
This is a genuine replacement light bulb for a refrigerator. The inside of your refrigerator should illuminate when you open the door. If your fridge does not illuminate, you may need to replace this ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
May 8, 2022
I'm not getting water to the icemaker, all the piping is unobstructed, water pressure is 55psi, new filter, ice valve is 181 ohms 18.2 vac present at unplugged conn; water valve r is 234 ohms 32 vac at unplugged conn and 120 vac when water is requested (cold water delivery works). When ice is requested only 27 vac is present at the ice dispenser water valve. Any ideas for me? Thank you in advance, Mike
For model number MFI2269DRH00
Hello Michael, Thank you for the question. Set your multitester to the R X 1 ohms setting to test for continuity. Place each of the multitester's leads on a terminal. Your multitester should display a reading between 200 and 500 ohms. Closely examine your water inlet valve. The exact ohm resistance rating you should test for may be marked on the valve. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Gordon
August 15, 2023
My right freezer drawer won't slide. How can these drawers be removed? Thanks!
For model number MFI2269DRH00
Hello Gordon, thank you for contacting us. Follow the following instructions to remove freezer drawers:
1- Open the freezer drawer to full extension.
2- Loosen the four screws attaching the drawer glides to the drawer front.
3- Lift drawer front upward and off the screws.
4- Use the small flathead screwdriver to pry the left slide rail tab away from the liner enough to release the drawer stop. Do the same to release the right drawer stop.
5- Now you can easily remove upper and lower drawers.
We hope this information helps!
Was this helpful?
Thank you for voting!
Ma
September 14, 2023
Do you have any available drawer frame cover replacement?
For model number MFI2269DRH00
Hello Ma, thank you for contacting us. The shelf frame for your model is part number PS11731402. We hope this information is useful!
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!
