Sold individually. This is a radiant surface element with a limiter, and it works in conjunction with your range. The function of this part is to give heat to the surface directly above it, on cooking area stovetop.
This part is a replacement halogen lamp for your oven. The bulb is 25 watts and 120 volts. If your light bulb is burned out, this is the part that replaces it. Be sure to turn off power to your range ...
This infinite switch for eight inch range burners is almost three inches long. This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the pro...
This is a replacement screw and washer for your oven/range. It is a Phillips-head screw approximately half an inch long, and the washer is approximately 1 inch in diameter. The screw attaches the oven...
$10.14
In Stock
Questions And Answers for MER6772BAW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
FRANK
January 8, 2020
Upper oven light will not turn off. Tried shutting down power by turning off at breaker, waiting 60 seconds, then restored power. Light remained on. Tried opening door and holding in sensor button on panel, light stayed on. Replaced the control panel about 2-3 years ago. All has been working fine since then until recent light problem.
For model number MER6772BAW
Hello FRANK and thank you for writing.
Possible Cause: Unseated Door
If the oven door does not connect with the door light switch, the oven light will stay on. To test, open the oven door and press the door light switch. If the light turns off, the door will need to be adjusted. If it does not the switch might be defective. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Claudette
December 14, 2021
The original part I'm looking for is 7403052460 (switch ignition) but it seems that it’s discontinued. Which part is replacing it. Maytag Gemini stove range.
For model number MER6772BAW
Hello Claudette, Thank you for the question. The 7403052460 is not showing to be a valid part number. If you need the switch to control the Dual Element you will need Part #: PS11744018. The Switch for the Small Element is Part #: PS11744486 and the Large Element Switch is Part #: PS11744487. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
After replacing the bottom oven baking element, it still will not heat up. The broiling element works fine. The control panel says it's on, but it doesn't work. Any ideas?
For model number MER6772BAW
Hello F, thank you for your question. Our two recommendations are the temperature sensors PS1570174 and PS11744537 and the control board PS2357564. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip charge. It was easy!!
Thermal switch is integral to element and can not be changed, must replace entire element.
Turn off power. Removed front two screws above oven door jamb and lifted the top. Removed the bracket that holds the element against the glass top and removed the element. Moved brackets from old element to new one, aligning to same numerical position and then moved wiring to new element. Slide new element under bracket and reinstalled single screw. Replaced top and screwed down. Turn on power and test .
