This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than...
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is do...
The idler pulley wheel is now sold with this arm. This idler pulley is for dryers.
Idler pulley maintains correct tension on the drive belt to spin the drum.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jack
February 8, 2020
2nd request for answer---the lint filter red light came on and the dryer (about 1 year old) will not start. It was clean but i cleaned it again still red light and no action. What next.
For model number MED5500FW0
Hi Jack. Sadly it looks like it could be a problem with the control board. Power-cycle your dryer and if this is still happening the board might need to be replaced. Thank you for your question and good luck with your repair.
The lint screen red light came on. The screen was clean but I cleaned it again. Dryer will not start.
For model number MED5500FW0
Hi Jack. Sadly we do not have information on these symptoms. I recommend contacting the manufacturer directly for assistance. Thank you for your question and good luck with your repair.
Was this helpful?
Thank you for voting!
Jeff
July 14, 2023
which way does the fan motor turn to come off, i can seem to get it to budge
For model number MED5500FW0
Hello Jeff, thank you for your inquiry. The part that you are referring to is the blower wheel. It blows air through the drum and out through the exhaust vent. You can easily replace the blower wheel by using the following instructions:
1. Turn off the dryer.
2. Remove the top panel.
3. Remove the control panel.
4. Remove the front panel.
5. Remove the top brace above the drum and dislocate the bulkhead.
6. Remove the drum.
7. Remove the blower cover and use socket wrench to remove the screw holding the blower wheel.
8. Turn the screw counter-clockwise to remove.
We hope this helps!
Was this helpful?
Thank you for voting!
April
October 13, 2023
When you push the start button it will not start
For model number MED5500FW0
Hi April, thank you for contacting us. We have found that the issue is with the door switch, part number PS12745626. The door switch prevents the dryer from running when the door is open. We hope this solves your problem!
I asked for advise, looked around and priced heating elements and thermostats. This was the best combo offered for the price given. It was shipped and received it very quick. Installed it and 5 minutes later, she was running like a champ!
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. Easy repair 15-30