This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$26.51
In Stock
Order within the next 5 hrs and your part ships today!
This part senses the flame for heat allowing the gas valve to open.This flame sensor is three inches long and is used for many gas clothes dryers.This flame sensor assembly is made of both plastic and metal.
$61.09
In Stock
Order within the next 5 hrs and your part ships today!
This part is the replacement thermal fuse for your dryer. When you order this part, you will receive the fuse itself, as well as the bracket that mounts it to the dryer. The thermal fuse is approximat...
$58.71
In Stock
Order within the next 5 hrs and your part ships today!
This conversion kit contains all parts needed to convert your gas dryer from natural gas (NG) to liquid propane (LP). This kit will work with some Samsung dryers as well. Use model # to ensure you are...
$68.41
In Stock
Order within the next 5 hrs and your part ships today!
This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees...
$75.95
In Stock
Order within the next 5 hrs and your part ships today!
Order within the next 5 hrs and your part ships today!
Questions And Answers for MDG9700AWM
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cathy
May 17, 2023
When dryer is plugged in you can hear a slight humming but not lights on the control panel and no power.
For model number MDG9700AWM
Hi Cathy, thank you for reaching out. If there is no power to the dryer, there is a possibility that the issue is related to the terminal block kit, part number PS334183, which might be burned out due to an electrical current surge. Flowing currents through your breaker box cause a slight hum. You also need to check the electrical wires in order to resolve the problem. We hope this helps, good luck with this repair!
Callled the service company to diagnose the problem. Watched him take machine apart. He found the problem. Told me the parts that I needed. Didnt know what they were. Went to partselect.com looked my model up and found parts and ordered. Followed same steps as repair guy: Two screws in back of machine then slide top off. Six screws in front to remove front door ( 4 screws on top 2 on bottom) Changed the thermostat and thermistor. Saved 320 dollars :)
From what I understand, this is a common problem with this Samsung made Maytag Neptune dryer. The dryer was making a sound like it had a shoe in it every time it was drying. The crack was in the seam at the back of the drum behind one of the baffolds so you can't see it when you look inside. I did not see it until I took the top off the dryer, looked inside and saw light through the hole. To take the dryer apart, first unhook it from the wall, gas, electricity, and exhaust. Remove 2 skrews from the top back side and slide the top of the dryer back and remove. The plastic control panel is then removed by taking 2 skrews out from the top, pulling the top of the control panel forward and reaching in with the other hand to pop out the plastic clips of the control panel from the front face of the dryer. Unplug the control panel from the electrical panel inside the dryer. Then you can remove the front door, 2 skrews, remove the front panel, 8 skrews I think, then the front piece the the drum rides on, 1 skrew. Take the belt loose and the drum will come right out. To install just reverse. Pretty easy once I figured out how to remove the control panel. I think the reason for the drum crack is it looks as though the back pressed metal piece that the drum rides on is not perfectly round. Even the new drum makes a very light thump sound and when I watched it go around with the top off the dryer I could see the drum turn slightly oblong. Check your wheels and make sure the axles are not worn, if they are, replace them at this time. Also you might as well replace the belt too.
Remove dryer covers and locate heater assembly. Removed heater assembly and checked visually if the heater coil is opened, I verified this with an ohm meter. Heater Continuity was OK. Next step I checked the heater sensors. Thermal fuse with bracket had no ohm meter reading between two terminals[open circuit]. Order part#35001193 "thermal fuse" with bracket from "partsSelect.com." Assemble back in reverse order. Please note that the dryer heater was filled with lint and needed a good cleaning.