This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.
$12.04
In Stock
Order within the next 4 hrs and your part ships today!
The spring for this part is sold separately.
This idler assembly is for dryers.
Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the ...
$45.51
In Stock
Order within the next 4 hrs and your part ships today!
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
$16.54
In Stock
Order within the next 4 hrs and your part ships today!
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.
$10.20
In Stock
Order within the next 4 hrs and your part ships today!
Questions And Answers for MDE3757AYW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wayne
July 11, 2023
Pain in the rear end the dryer will heat and then it'll stop and we can wait a while and open the door and then close it back and they'll start back again but the dial is not moving on the dryer
For model number MDE3757AYW
Hi Wayne, thank you for the question. Based on our understanding of the issue, we would suggest checking the timer, part number PS11741924, to fix the issue. This dryer timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting. We hope this solves your problem!
dryer stars ,heat comes on and immediatly it cuts off heating. checked heater,fuse,&heater thermostat continuity. seems ok. what could be the problem.
found ceramic insulator on heating element little loose and wire connected to one of the heater terminal going to heating thermostat burnt.I replaced it .still the same problem
For model number MDE3757AYW
Hello Sajjad, thank you for reaching out. According to our research, the issue is with the timer, part number PS11741924. It controls the electrical components and the duration of the dryer cycles. We hope this information helps!
my dryer works however sometimes will not heat and other time heats for say 10 minutes then stops heating . Then 5-6 hrs later we turn it on and it heats for a wile
Last February I replaced the high limit thermal fuse and has work well up to know I believe that this must be a new issue.
For model number MDE3757AYW
Hi Frank, thank you for the question. Based on the description that you have provided, we would recommend checking the cycling thermostat, part number PS11741918, which continually cycles the heating element off and on to maintain a constant inner temperature. If this part is faulty, you may need to replace it. We hope this is helpful!
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to. Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer. The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!