This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.
$12.04
In Stock
Order within the next 1 hr and 31 mins and your part ships today!
The spring for this part is sold separately.
This idler assembly is for dryers.
Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the ...
$45.51
In Stock
Order within the next 1 hr and 31 mins and your part ships today!
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
$16.54
In Stock
Order within the next 1 hr and 31 mins and your part ships today!
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.
$10.20
In Stock
Order within the next 1 hr and 31 mins and your part ships today!
Questions And Answers for MDE3706AYW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Angela
February 9, 2020
Why might this model start making an awful noise when running? Also no heat
For model number MDE3706AYW
Hello Angela, thank you for your question. The noise could be caused by the rollers, belt, idler pulley, felt seal or the roller shafts. We would recommend checking over those parts for wear and tear. There should be visible wear on those parts. If the unit isn't heating, that could be an issue with one of the thermostats or the heater. The thermostats and element can be tested for continuity to determine if any of those parts have failed. I hope this helps.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Bill
August 30, 2022
How to replace a thermal switch
For model number MDE3706AYW
Hi Bill, thank you for reaching out. We have researched your model and found a relevant video that will help you in replacing the thermal switch. We hope this helps. Please submit a new question if you have any follow ups!
2 people found this helpful.
Was this helpful?
Thank you for voting!
RANDY
February 23, 2024
The moter runs but won't turn the drum it will turn with nothing in it
For model number MDE3706AYW
Hello Randy, thank you for reaching out. According to our research, the issue is most probably with the weak drive motor. You may need to replace the drive motor, part number PS11739459, to fix the issue. We hope this solves your problem!
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to. Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer. The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!