This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the b...
$153.18
In Stock
Order within the next 11 hrs and your part ships today!
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
$89.04
In Stock
Order within the next 11 hrs and your part ships today!
This is a replacement lid switch actuating cam for your washer. The cam is located on the underside of the washer lid, near the hinge. The cam actuates the lid switch, so your washer knows the lid is ...
$12.45
In Stock
Order within the next 11 hrs and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$153.03
In Stock
Order within the next 11 hrs and your part ships today!
This part is the replacement motor pivot spring for your washer. It is made of metal and is approximately 3 inches long and 2 inches wide. The motor pivot spring helps hold the drive motor in the corr...
$12.45
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for MAVT634AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ray
October 12, 2023
MY WASHER DOESN'T START. NOTHING. DEAD. HAPPENED BETWEEN CYCLES. THE TIMER HAS BEEN SEEMINGLY GOING BAD AS YOU SOMETIMES HAVE TO MANUALLY MOVE IT TO NEXT CYCLE. COULD THIS BE MY ONLY PROBLEM? IN YOUR SYMPTOMS LISTED FOR NOT STARTING AT ALL, THE TIMER IS NOT MENTIONED.
For model number MAVT634AWW
Hi Ray, thank you for the question. First, you may need to make sure that there is power coming to the washer. If the washer has power but it still does not turn on, then you may need to check the timer, part number PS11739503, as it is the most likely cause of this issue and may need to be replaced. We hope this sorts out your problem!
As soon as agitation cycle starts there is a unusual loud noise. Spin cycle runs ok.
For model number MAVT634AWW
Hi Thakore, thank you for reaching out. Based on the description that you have provided, the issue is with the tub seal and bearing kit. The tub bearing helps to keep the inner tub spinning smoothly. You may need to replace the tub bearing kit to fix the issue. The part number is PS2349020. We hope this information helps!
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed. Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.