LSFD2591ST LG Refrigerator - Overview

Diagrams for LSFD2591ST

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Air Cleaner Filter Assembly – Part Number: ADQ73214408
$41.67
In Stock
Air Cleaner Filter Assembly
Part #ADQ73214408
This air filter helps keep your fridge smelling fresh and your food lasting longer. It uses carbon to trap odors and clean the air inside your refrigerator. If you notice bad smells or your fridge tells you it’s time, it’s probably time to replace the filter—usually every six months. It fits LG and some Kenmore Elite models. To install, just turn off the power, swap out the old filter, and reset the filter light once the new one’s in place.
Refrigerator Water Filter LT700P – Part Number: AGF80300702
$77.99
In Stock
Refrigerator Water Filter LT700P
★★★★★
★★★★★
(4)
Part #AGF80300702
This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
Handle Screw – Part Number: MJB63190001
$13.15
In Stock
Handle Screw
★★★★★
★★★★★
(2)
Part #MJB63190001
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as they commonly wear at the same rate. This is about 1 inch long and metallic in color.
Door Shelf Bin Assembly – Part Number: AAP73252302
$60.45
In Stock
Door Shelf Bin Assembly
★★★★★
★★★★★
(2)
Part #AAP73252302
This refrigerator door shelf bin is a clear, gallon-sized storage accessory designed for installation on the right-side door of select refrigerator models. Crafted from durable, food-safe resin, it features a transparent body with a white band along the top edge, allowing easy visibility of stored items. Measuring approximately [insert dimensions if known], it provides ample space for organizing beverages, condiments, and jars. Installation is straightforward and requires no tools, making it a convenient replacement option. While primarily designed for specific refrigerator models, it’s important to verify compatibility before purchase. Some versions may include an integrated soda can organizer for added functionality.
Water Dispenser Button – Part Number: ABH74219603
$69.25
In Stock
Water Dispenser Button
Part #ABH74219603
Refrigerator Water Reservoir – Part Number: AJL72911502
$67.05
In Stock
Refrigerator Water Reservoir
★★★★★
★★★★★
(2)
Part #AJL72911502
The water reservoir holds the water for the water dispenser as the water chills.
WATER INLET VALVE – Part Number: AJU72992603
$120.78
In Stock
WATER INLET VALVE
Part #AJU72992603
Water Filter Bypass Plug – Part Number: ABN73019101
$38.19
In Stock
Water Filter Bypass Plug
Part #ABN73019101
Door Holder – Part Number: MEG61899901
$20.85
Special Order
Door Holder
★★★★★
★★★★★
(1)
Part #MEG61899901
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
Refrigerator Push Button Switch – Part Number: 6600JB3007K
$47.07
Special Order
Conroller Assembly – Part Number: 6615JB2005R
$54.95
In Stock
Conroller Assembly
Part #6615JB2005R
Ice Maker Assembly - 3 Wire – Part Number: AEQ73110203
$341.03
In Stock
Ice Maker Assembly - 3 Wire
Part #AEQ73110203
NOTE: The Secondary (smaller) wire connector has 3 wires in it. If original ice maker has 6 wire connector see part number AEQ73110205. Please verify connector before ordering.

Common Symptoms of the LSFD2591ST

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice / water dispenser control panel cover discolored at bottom due to splashing water
16 of 20 people found this instruction helpful.
  • James from ST AUGUSTINE, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I suggest turning off the water valve and power to the refrig before starting work. If this is not done the water dispenser will probably spray water down the front of the refrig. The whole icemaker assembly must be pulled out from the front. It is a friction fit--just insert fingers in the ice chute and pull out. The entire piece will pu ll out from the door. The control panel cover is held in by 8 screws that extend through the circuit board to the cover. It is a good idea to unplug the wiring to the circuit board when replacing the cover to prevent tension damage to the small guage wires. Once the new control panel cover is attached to the circuit board, the whole assembly can be reinstalled into the door.
Was this helpful?
Thank you for voting!
The water dispenser lever came off, due to broken tabs in the door panel.
12 of 17 people found this instruction helpful.
  • MARK from CLAREMORE, OK
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Before you begin, I'd recommend unplugging the refrigerator. You have to slip the putty knife in around the edge of the dispenser panel and carefully release the tabs all the way around and the entire panel pulls straight out. There are three wiring harnesses to unplug. You'll have to remove several screws and release the tabs around the electronic panel and remove it from the main panel. It's a good idea to take note or even pictures of how the ice and water actuators are positioned on the panel, so you get them situated properly on the new panel. If the ice actuator is not fit correctly on a knob that sticks up it may dispense ice all the time (happened to me). After you transfer the actuators to the new panel and the ice and water dispensing levers, you can re-attach the electronic panel on the left side. make sure all of the wiring harnesses are plugged in and the wires situated out of the way, then re-install the panel by pushing it straight back in. Plug the refrigerator in and test it out.
Was this helpful?
Thank you for voting!
The lights wouldn't always come on.
4 of 6 people found this instruction helpful.
  • Linda from VALE, OR
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I actually watched a YouTube video for LG refrigerators. The hardest part was taking the wire harness out. Mine was really stuck in there. But got it, put the new switch in and viola it worked. Yay!
Was this helpful?
Thank you for voting!