LRSCS21935TT LG Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Plastic Tube - 5/16 Inch – Part Number: MJU62070602
$32.95
In Stock
Refrigerator Door Switch – Part Number: 6600JB1010A
$46.15
In Stock
Connector,Tube – Part Number: 4932JA3009A
$20.85
Special Order
Connector,Tube
Part #4932JA3009A
Ice Tray – Part Number: 3390JA1150A
$16.45
In Stock
Ice Tray
Part #3390JA1150A
This part is the replacement ice tray for your refrigerator. The tray is made of white plastic and is approximately 9 inches in length, and 3 inches in width. It has the capacity for 8 ice cubes. The ice tray can be filled up with water and is the mold that shapes the ice cubes. If your current ice tray is cracked, warped, or if mineral deposits have settled inside it, it may cause the ice cubes to stick. This part is sold individually and is an authentic OEM part.
Micro Switch – Part Number: 6600JB3001C
$35.15
In Stock
Micro Switch
Part #6600JB3001C
Refrigerator Water Tube Fitting – Part Number: 4932JA3002A
$35.15
In Stock
Refrigerator Water Tube Fitting
Part #4932JA3002A
The water tube fitting connects lines that supply water to components such as the ice maker and water dispenser.
Plastic Tubing - 5/16 Inch – Part Number: MJU62070603
$29.65
In Stock
Plastic Tubing - 5/16 Inch
Part #MJU62070603
This part is the replacement water line for your refrigerator. It is a long plastic tube, which is 5/16 of an inch in diameter. If your refrigerator is leaking, or if it will not dispense water or ice, you may have a damaged water line. When you replace the water line, you may want to pick up a new water tube union as well. You can use a utility knife to cut the old water line where it is damaged, and use the union to attach the new water line to the old one. This tubing is sold individually and is an OEM part.
Light Bulb – Part Number: 6912JB2004M
No Longer Available
Light Bulb
Part #6912JB2004M
FAN ASSEMBLY – Part Number: 5901JA1012B
$30.75
In Stock
FAN ASSEMBLY
Part #5901JA1012B
For refrigerator air circulation, this OEM fan assembly is listed for select models. Check your refrigerator’s model number to confirm compatibility.
Overload Protect – Part Number: 6750C-0004R
$40.65
In Stock
Overload Protect
Part #6750C-0004R
Thermistor Assembly,PTC – Part Number: 6748C-0002C
$47.25
Special Order
Thermistor Assembly,PTC
Part #6748C-0002C
Refrigerator Plastic Tube – Part Number: 5210JA3005A
$20.85
Special Order
Refrigerator Plastic Tube
Part #5210JA3005A

Common Symptoms of the LRSCS21935TT

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Remove and replace light switch
45 of 91 people found this instruction helpful.
  • Debbie from Waltham, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
Evaporator Fan Squeeking
17 of 21 people found this instruction helpful.
  • Kyle from WOODBURY, MN
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Wrench (Adjustable)
Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin . From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!
Was this helpful?
Thank you for voting!
Water feed line running from water valve to filter housing was leaking
13 of 21 people found this instruction helpful.
  • Tom from EASTON, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
Was this helpful?
Thank you for voting!