Models
>
LRG3095ST
LRG3095ST (FS1ELGA) LG Range - Overview
Sections of the LRG3095ST
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Range Convection Fan Motor
PartSelect #: PS7791924
Manufacturer #: EAU61865301
This part is the replacement A/C fan motor or convection fan motor for your range. It is used to spin the fan blade, which circulates hot air through the oven, and ensures even heating. If you notice ...
$173.67
In Stock
Burner Knob - Stainless Steel
PartSelect #: PS7321756
Manufacturer #: AEZ73453509
Sold individually. This knob accepts a D-shaped shaft.
$145.44
In Stock
TRANSFORMER ASSEMBLY,POWER
PartSelect #: PS16732632
Manufacturer #: EBJ64465501
The spark module controls the spark for lighting the cooktop surface burners.
$71.70
In Stock
CAP,BURNER
PartSelect #: PS3627296
Manufacturer #: MBL61908604
The burner cap attaches to the top of the burner head and acts like a cover for the burner head. This part helps to protect the burner from spills and helps to even the flame while cooking. The cap is...
$82.09
Special Order
Questions And Answers for LRG3095ST
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the LRG3095ST
[Viewing 6 of 6]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Inner Oven glass because it shattered
Go onto youtube, such as https://www.youtube.com/watch?v=-ITkrwhDNMQ and watch similar videos for DYI. The process is very similar to other models.
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know the process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
Hope this helps
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know the process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
Hope this helps
Parts Used:
-
Jeffrey from CERRITOS, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
11 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't ignite
Took off the oven door then took out the racks and two screws in the oven bottom and removed it . Then removed the heat deflector. Then un plugged the old igniter and removed the burner to make it easier to remove the old igniter. Then installed the new igniter and reversed the process
Parts Used:
-
Martin from KEWASKUM, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not light
As soon as my husband put it in the oven, the very thin prongs broke. There was no guard on either side of the prongs for protection like the one that had been in there. Very costly to us of $185 with no fix. Very disappointed in that ignitor. It would have been an easy fix. Had replaced one previously but it only lasted 6 months. Now we have a new stove
Parts Used:
-
Sheila from HOPKINTON, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
6 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!