LRE5602SW LG - Overview

Models starting with LRE5602SW

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Temperature Sensor – Part Number: EBG61305805
$59.35
In Stock
Temperature Sensor
★★★★★
★★★★★
(5)
Part #EBG61305805
This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor internal temperatures and regulate heating or cooling elements accordingly. If your appliance is experiencing inconsistent temperature control, the sensor may be defective and can be tested using a multimeter for continuity. Refer to your user manual for exact placement and diagnostic procedures. Sold individually.
Bake Element – Part Number: MEE36593201
$181.62
In Stock
WINDOW,GLASS – Part Number: 4890W1N009H
$125.28
In Stock
WINDOW,GLASS
★★★★★
★★★★★
(2)
Part #4890W1N009H
This clear inner glass lets you see inside your LG oven while keeping the heat in. If your oven glass is cracked or chipped, replacing it helps restore energy efficiency and safe cooking. It’s made to fit specific LG models, so check your oven’s model number before installing. Easy to replace with basic tools.
Time Delay Fuse – Part Number: 3B74133Q
$13.15
In Stock
Time Delay Fuse
★★★★★
★★★★★
(1)
Part #3B74133Q
Sold individually.
FOOT – Part Number: 4778W1N001B
$21.95
In Stock
FOOT
Part #4778W1N001B
Range Radiation Heater – Part Number: MEE62385201
$198.03
Special Order
Range Radiation Heater
★★★★★
★★★★★
(3)
Part #MEE62385201
A dual radiant heater supplies heat to a cooking area beneath a glass cooktop. Replacement may be needed when one zone does not warm, only the inner or outer section works, or the element has a visible break. Normal radiant burners cycle on and off, so cycling alone does not prove a failure. Check the control switch and connections first, then match the replacement by full model number, location, size, mounting points, and electrical rating. Disconnect the range at the breaker and confirm the circuit is dead before service. Handle sharp metal edges and the glass top carefully, and return every bracket, shield, and wire to its original position.
Range Oven Relay Control Board – Part Number: 6871W1N012B
$195.00
Special Order
Range Oven Relay Control Board
Part #6871W1N012B
Radiant Heater – Part Number: 5300W1R004A
$134.16
In Stock
Radiant Heater – Part Number: 5300W1R005A
$310.19
Special Order
SHELF – Part Number: MHL39256107
$99.52
In Stock
SHELF
★★★★★
★★★★★
(1)
Part #MHL39256107
Upgrade your oven with this durable gliding shelf rack, designed to provide a stable surface for baking, roasting, and broiling. Its smooth sliding design makes it easy to insert and remove dishes, offering convenience and efficiency during cooking. Built to support heavy cookware, this rack measures approximately 24 3/8" x 16 1/2" and features a sturdy construction for long-lasting performance. Cleanup is simple thanks to its smooth finish, making it a practical and reliable addition to your kitchen. Installation is quick—just slide the rack into the designated oven supports for immediate use.
Screw,Taptite – Part Number: 1SBF0402418
$13.15
On Order
Screw,Taptite
Part #1SBF0402418
Control Board Sub Assembly – Part Number: EBR73323501
$130.62
Special Order
Control Board Sub Assembly
Part #EBR73323501
This control board sub assembly manages essential appliance functions, ensuring smooth operation and accurate performance. Ideal for replacing a faulty board that causes error codes or unresponsive controls, it restores reliability and efficiency. Installation requires disconnecting power and mounting the new board according to your appliance’s specifications.

Common Symptoms of models starting with LRE5602SW

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hammer 1, Glass range top and heating element 0
24 of 56 people found this instruction helpful.
  • Richard from CHESAPEAKE, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution:
1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet.
2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Was this helpful?
Thank you for voting!
No heat in oven mode
8 of 11 people found this instruction helpful.
  • Dennis from CARY, IL
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Verified P/N with LG. Took a few days . They sent names of several suppliers, cost was almost double. Ordered part from P/S, here in 2 days. Watched video on you tube. Unplugged, took off back, unplugged bake element, removed power box. The opening for bake element is still attached to rear panel by tiny bits of sheet metal. Used Dremel w ith cut-off wheel to cut thru nibs & deburr opening. this panel has to be removed, it rests on bottom panel & is held in position by power box. Removed bake element carefully, front of element broken, tried to put new element in, would not fit. Had to grind notches in bottom panel down to clear supports on new element. This did the trick. back together quick & no problems. If had to do again estimate less than 1 hour.. By the way am 81 yrs. young.
Was this helpful?
Thank you for voting!
Oven would initially start to heat up but would not hold its temp
7 of 9 people found this instruction helpful.
  • Leonard from Plano, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I searched online and found someone that seemed to have the exact problem. That person had replaced the lower burner and the same PCB board I replaced. I was able to test the lower burner without removing it and it tested OK. The PCB board in the article I had checked was burned and obviously bad but mine was not. I took a chance and ordered just the PCB board. I replaced this board and the oven now works perfectly. I seems this board was not turning on the bottom burner but the system thought it was working fine.
Was this helpful?
Thank you for voting!