LRE3027ST LG Range - Overview
Sections of the LRE3027ST
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Temperature Sensor
PartSelect #: PS11732697
Manufacturer #: EBG61305805
This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor inter...
$59.35
In Stock
WINDOW,GLASS
PartSelect #: PS16661222
Manufacturer #: 4890W1N009H
This clear inner glass lets you see inside your LG oven while keeping the heat in. If your oven glass is cracked or chipped, replacing it helps restore energy efficiency and safe cooking. It’s made to...
$125.28
In Stock
HEATER,SHEATH
PartSelect #: PS12582156
Manufacturer #: MEE32902206
This sheathed heater provides controlled heat for appliance operation while protecting internal components. Its protective casing supports durability and consistent heating performance.
$65.95
In Stock
PCB ASSEMBLY
PartSelect #: PS7792813
Manufacturer #: EBR74164801
This printed circuit board assembly manages electronic signals and system communication. It plays a key role in coordinating appliance functions and supporting reliable, responsive performance.
$171.28
In Stock
Common Symptoms of the LRE3027ST
[Viewing 9 of 9]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
No heat
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Hammer 1, Glass range top and heating element 0
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution:
1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet.
2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet.
2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Parts Used:
-
Richard from CHESAPEAKE, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
22 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Convection bake fan would not shut off
Looked at schematic to follow circuitry. Checked online for advice. Most online advice suggested replacing thermostat. Thermostat is not in controlling fan circuit!
PCB is only circuit controlling fan on and off. I unplugged fan so as to use rest of range until I received and installed PCB. Works fine now. Note: I have electronics background and can read most circuitry.
PCB is only circuit controlling fan on and off. I unplugged fan so as to use rest of range until I received and installed PCB. Works fine now. Note: I have electronics background and can read most circuitry.
Parts Used:
-
David from SOUTH HAVEN, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom heat element went out
Checked element no reading. Took off back panel and removed element. Took 5 days to get element. Put in new one. Took 20 minutes. Did not have to cut panel as video had shown. It had screws and was easy to get out and put the new one in. The new element was exactly the same as the old one. I checked all elements before ordering. Was satisfied with everything but the delivery time
Parts Used:
-
Jack from LEXINGTON, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
5 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!