LFXS28596M LG Refrigerator - Instructions

1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.

Had to buy the entire door mullion because the spring broke, wasn't happy. Got the new part very quickly and it was a new replacement part number. Somewhat tentative. Took it out of the box and looked it over. No spring! Groan! Thought I got the wrong part. Flipped the bottom hinge and it snapped open, no need for a spring! Two screws, disconnect the wire harness, throw away the old, get new, connect the wire harness, connect hinges, put in two screws! Super easy. Watch the video for some pointers along the way.

This couldn't have been easier. Two tiny screws in the front needed unscrewed, and then two plastic clips in the middle just had to be popped lose. Finally, you unplugged the power cord. Then, you just needed to reverse the process by plugging the new ice maker in, popping the clips in place, and screwing the two holes back in and turning the whole thing on. Voila! Perfect ice cubes again. And for only a little over $100.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order

Watched a YouTube video on how to replace the door flipper (mullion). Very easy to unscrew the plate and disconnect the electrical circuit. Then gently slide up the flipper and replace with a new one.

Found the part on Parts Select. Ordered the part, which came quickly. While waiting for delivery. I watched a short video on how to replace this part. I'm a 73 yr. old female, and no trouble at all. I really felt a sense of accomplishment. Thank you Parts Select.

Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done

This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!

Replaced with new mullion

Unplug the refrigerator and empty the freezer. Remove the lower basket and roll out upper tray. Open the freezer door. I was able to lie on the floor to remove the 2 screws holding the ice maker without removing the
freezer door. Depress the 2 tabs and slide the ice maker forward to remove. Install in reverse order. Change the water inlet valve at the same time.

Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.

Installed new one.

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.