This is a genuine replacement switch. It is a push button style switch that is designed for use in your refrigerator. When the door of your appliance is opened the switch is released, and the light co...
$47.07
In Stock
Order within the next 7 hrs and your part ships today!
This OEM filter measures 2.5 inches deep, 12.5 inches high, 5 inches wide and roughly 1.5 lbs. It is recommended to replace this filter every six months or 300 gallons, whichever comes first. If you n...
$109.81
In Stock
Order within the next 7 hrs and your part ships today!
This 13-volt evaporator fan motor helps circulate air over the refrigerator coils. These coils will then convert the heat into cool air, which is then circulated from the freezer section to the fresh ...
$243.17
In Stock
Order within the next 7 hrs and your part ships today!
Keep your refrigerator running efficiently with this defrost sensor and thermistor assembly. It monitors the evaporator coil temperature to help regulate the defrost cycle, preventing frost buildup an...
$56.75
In Stock
Order within the next 7 hrs and your part ships today!
Tired of running out of ice? This complete ice maker kit is a simple way to get your fridge making ice again. It includes everything you need—the ice maker, housing, and control unit—to keep a steady ...
$380.34
In Stock
Order within the next 7 hrs and your part ships today!
Order within the next 7 hrs and your part ships today!
Questions And Answers for LFX21960ST
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kurt
November 3, 2022
Fails occasionally. When plugged in, it powers up for a short time and then goes dark. Everything turns off and there are no lights on the front panel.
If I use test mode I can get the compressor to run. After cycling through test modes a few time it works again. One of the issues I have is there is not a compressor relay attached to the compressor like all the diagrams show, but a secondary control board with a cable to the compressor. I’m wondering if it’s the main control board, but since there is a secondary board I’m not sure.
For model number LFX21960ST
Hello Kurt, thank you for contacting us. The issue you described is probably related to the main control board which is connected to the compressor via a cable. We would recommend replacing the main control board, part number PS3533719. The secondary control board is responsible for managing dispenser functions. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have continuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.
