This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
$161.95
In Stock
Questions And Answers for LEQ2152HS0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Yulanda
January 18, 2023
When I shut the door the control board panel blinks very rapidly and it the dryer will not start.
For model number LEQ2152HS0
Hi Yulanda, thank you for reaching out. You need to check the door switch, part number PS2330880, and the control board, part number PS12724036, to fix the issue. We hope this solves your problem! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
I have inquired a washer and dryer set and the dryer won’t power on at all… there’s power going from the outlet to the cord to the dryer. But the dryer doesn’t light up or start. Would it be the thermal fuse? Or something esle?
For model number LEQ2152HS0
Hi Nick, thank you for the question. Based on our understanding of the issue, we would suggest you check the thermal fuse, part number PS419402, as it is the most likely cause of this issue. If it is faulty, you may need to replace it. We hope this solves your problem!
Greetings!
Where do I find the Moisture Sensor?
Thank you.
For model number LEQ2152HS0
Hi Mark, thank you for reaching out. According to our research, the moisture sensor comes with the lint filter cover, part number PS627383. We hope this helps!
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.