LDT5665WW LG Dishwasher - Overview

Diagrams for LDT5665WW

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dishwasher Holder – Part Number: MEG64438801
$13.15
In Stock
Dishwasher Holder
★★★★★
★★★★★
(4)
Part #MEG64438801
This gray mounting bracket is designed to securely hold the dish rack in place inside your dishwasher during operation. Measuring 1 inch by 1 inch, it ensures stability and helps prevent the rack from shifting or causing internal damage. If the holder becomes broken or goes missing, replacing it is essential to maintain proper rack alignment. Each bracket is sold individually and installs easily by snapping into the designated slot.
Dishwasher Roller Assembly – Part Number: 4581DD3003C
$13.15
In Stock
Dishwasher Roller Assembly
★★★★★
★★★★★
(8)
Part #4581DD3003C
The dishwasher roller assembly connects to the dishrack, and is located in the lower level of the dishwasher. It allows the dishrack to easily slide in and out. If the lower rack keeps falling off the track in your dishwasher, makes noises, the door will not close, or the dishes are not getting clean, then it is best to replace it for more security. A flat blade screw driver is the only tool needed for this installation. Open the lower dishwasher rack and remove retaining tabs from both ends of the rack and slide it out. Locate the older roll assembly, remove it and replace the rollers. Remember to put the tabs on each side back before sliding it back in. Make sure the dishwasher is off before starting this installation project.
Dishwasher Holder – Part Number: MEG64438901
$13.15
In Stock
Gasket – Part Number: 3920DD3005H
$69.25
In Stock
Gasket
★★★★★
★★★★★
(6)
Part #3920DD3005H
If your dishwasher is leaking or not cleaning as well as it used to, the door gasket might be the culprit. This flexible rubber seal fits around the tub and keeps water and steam inside during each cycle. It’s tough enough to handle heat and wear, and replacing it can fix common problems like water on the floor or poor wash results. Installation is simple—just press it into the groove around the door and you’re good to go.
Diverter Motor - 120V 60Hz – Part Number: 4681ED3001D
$51.65
In Stock
GASKET – Part Number: MDS65210402
$63.75
On Order
Hose Drain Assembly – Part Number: AEM74333104
$82.45
In Stock
Hose Drain Assembly
★★★★★
★★★★★
(6)
Part #AEM74333104
This drain hose assembly is designed for use with select LG washing machines and includes both the flexible rubber hose and plastic connectors. It efficiently channels used water from the washer tub to a designated drainage system, such as a standpipe or laundry sink. Over time, the hose may become clogged, dislodged, or damaged by foreign objects or external impact. Signs of a faulty hose include standing water in the tub, leaks, mold growth, or overflow. Prompt replacement is recommended to maintain proper washer performance. Installation requires only basic tools and should be done with the appliance powered off.
HOLDER – Part Number: MEG64438701
$13.15
In Stock
HOLDER
Part #MEG64438701
Dishwasher Water Inlet Valve – Part Number: 5221DD1001E
$80.25
In Stock
Dishwasher Water Inlet Valve
★★★★★
★★★★★
(1)
Part #5221DD1001E
This part is the replacement inlet valve for your dishwasher. It is approximately 4-1/2 inches by 3-1/2 inches. The water inlet valve in your dishwasher connects to the water source and solenoid wires, and ensures the tub has the right amount of water entering it. If your dishwasher continues to fill after it is full, or if it fills slowly, you may need to replace this valve. Another indication that your valve is damaged and will need to be replaced, is if you notice it is leaking when the dishwasher fills up. Before you begin this repair, be sure to disconnect the water and power sources from your washer. This part is sold individually and is an authentic OEM part.
HOLDER – Part Number: MEG64438902
$13.15
In Stock
HOLDER
Part #MEG64438902
This grey tine row retainer is designed to securely hold the horizontal tine rows on your dishwasher rack, keeping them in place so dishes stay organized and stable throughout each wash cycle. It clips directly onto the rack to prevent tines from loosening or shifting, helping maintain proper spacing for plates, bowls, and cookware. A worn or broken retainer may cause the rack to feel loose or rattle during operation, making replacement necessary for smooth performance. Installation is quick and simply involves attaching the clip to the designated spot on the rack to restore proper support.
ACCESSORY ASSEMBLY – Part Number: 5001DD4001H
$39.55
In Stock
ACCESSORY ASSEMBLY
Part #5001DD4001H
RACK – Part Number: MGR62482102
$36.25
In Stock
RACK
Part #MGR62482102

Common Symptoms of the LDT5665WW

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dishwasher leaking; got AE error almost every other wash
12 of 20 people found this instruction helpful.
  • Bruce from Katy, TX
  • Really Easy
  • 30 - 60 mins
The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.
Was this helpful?
Thank you for voting!
Second roller in on the left side was missing don't ask my how, pulling the bottom rack out the rack would dip down i had to lift it up to pull it the rest of the way out.
9 of 17 people found this instruction helpful.
  • Lenny from KIRTLAND, OH
  • Very Easy
  • Less than 15 mins
Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.
Was this helpful?
Thank you for voting!
Dishwasher was making loud grinding/buzzing noise
4 of 6 people found this instruction helpful.
  • Jon from GARDNERVILLE, NV
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Inst alled new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.
Was this helpful?
Thank you for voting!