LDG3016ST (FSTELGA) LG Range - Overview
Sections of the LDG3016ST
[Viewing 6 of 6]
Manuals & Care Guides for LDG3016ST
Click to downloadKeep searches simple, eg. "belt" or "pump".
Temperature Sensor
PartSelect #: PS11732697
Manufacturer #: EBG61305805
This temperature sensor, also referred to as a thermistor, is a genuine replacement component compatible with various appliance models. It works in coordination with the control board to monitor inter...
$59.35
In Stock
Oven Igniter
PartSelect #: PS3535362
Manufacturer #: MEE61841401
This gas range oven igniter is compatible with various models of LG gas ranges. It is made up of the igniter element, wire harness, connector and mounting bracket. The igniter is responsible for gener...
$317.43
In Stock
Burner Knob - Stainless Steel
PartSelect #: PS7321756
Manufacturer #: AEZ73453509
Sold individually. This knob accepts a D-shaped shaft.
$128.10
In Stock
Power Transformer Assembly
PartSelect #: PS16732632
Manufacturer #: EBJ64465501
The spark module controls the spark for lighting the cooktop surface burners.
$65.95
In Stock
Common Symptoms of the LDG3016ST
[Viewing 6 of 6]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven wouldn't ignite
Took off the oven door then took out the racks and two screws in the oven bottom and removed it . Then removed the heat deflector. Then un plugged the old igniter and removed the burner to make it easier to remove the old igniter. Then installed the new igniter and reversed the process
Parts Used:
-
Martin from KEWASKUM, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
11 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F3 Error Code
F3 Error code. Most documentation suggested checking oven sensors. They were good (Checked 1050 & 1080 Ohms). Next most common problem was bad connection somewhere. This was not problem. Documentation then suggested it would be main system board. This did not fix problem. If I shut power off disconnected key pad error F3 did not come back (although the PF power failure stayed on as no key pad). If I shut power off and plugged in key pad PF (power failure) came on and in a short time F3 appeared. I changed key pad and problem is gone.
Parts Used:
-
George from CORTLAND, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both ovens would not light
Remove oven bottoms Removed burners Remove igniters Pull out oven removed back disconnect wiring Installed new parts on burner made wiring hook ups Installed oven back and oven bottoms Tested and both work Took so long because I’m 75 years old Thanks for the proper parts
Parts Used:
-
George from Meadows Place, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!