The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
$41.42
In Stock
Order within the next 11 hrs and your part ships today!
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
$18.74
In Stock
Order within the next 11 hrs and your part ships today!
This lint filter screen is slide in styl type of Maytag filter screen. It is most typically used for the 08 and later series of Maytag gas or electric clothes dryers that appear before 1990.
$31.94
In Stock
Order within the next 11 hrs and your part ships today!
This dryer door latch kit comes in two pieces: a door latch, and a door strike. It's used to help hold your door shut to your dryer.
$12.64
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for LDE313
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
George
December 7, 2021
Dryer gets warm but not as hot as it should be. There's asn electrical part that controls that what is it?
For model number LDE313
Hi George,
Thank you for your question. If your dryer is not hot enough, the part that fixes the issue most of the time is the high limit thermostat. If the thermostat is fine, there are some other parts that you will need to check to see which one is causing the issue. You will also need to check the heater assembly, the heater element, the blower wheel with clamp, the jumper wires, the cycling thermostat, the thermal fuse, the heating element terminal and insulator and the belt. You will find information on how to test these parts under Free Repair Help and Instant Repairman on our website. We hope this helps! Good luck with the repair!
Would bad drum rollers cause a burning smell. They've been bad for quite awhile
For model number LDE313
Hello Valerie, Thank you for the question. If the Rubber is worn, it can cause a burning smell. The worn Rollers can also put wear on the Belt and cause the smell so we suggest checking the Belt for wear as well. We hope this helps!
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job. Thank you.
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.