KGCU483VSS00 KitchenAid Cooktop - Overview

Diagrams for KGCU483VSS00

See every part. Know exactly what you need.

Parts for the KGCU483VSS00

$108.62

Range Temperature Sensor

★★★★★

(27)

Part #WPW10131825

This temperature sensor detects the temperature within the oven cavity.

$30.40

Screw

★★★★★

(5)

Part #W11233072

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$17.95

Grate Feet - Kit of 4

★★★★★

(4)

Part #W10185266

This kit contains 4 grate feet for a range. These are the feet to fit your burner grates so the burner will not scratch your cooktop. The are black in color and made of rubber. These feet are fitted with a specific fire-resistant adhesive. If necessary, be sure to order adhesive separately. Be sure your burners are off and have cooled down to the touch before replacing these parts.

$10.40

Dryer Screw

Part #WP90767

This screw is sold individually.

$30.40

Washer Screw

Part #W11404293

Sold individually.

$9.85

Range Screw

Part #WP74003976

This screw is sold individually.

$47.25

WOK RING

Part #W10216179

$41.71

Surface Ignitor

Part #WPW10250406

ELECTRODE (LF & RF) (DUAL)

$22.24

Palnut

Part #7103P166-60

Sold individually.

$398.97

Grate Kit

Part #W11569347

$43.95

Surface Ignitor

Part #WPW10160235

$63.75

Surface Ignitor

Part #WPW10145991

ELECTRODE (CR)

Manuals & Care Guides for KGCU483VSS00

Click to download

Install

Installation Instructions

(1.76MB)

Install

Installation Instructions

Product Specifications Sheet

(0.27MB)

Common Symptoms of the KGCU483VSS00

How this model fails, and the parts that fix it.

Oven is too hot

Fixed by
these parts

Show All

Little to no heat when baking

Fixed by
these parts

Show All

Oven not heating evenly

Element will not heat

Fixed by
these parts

Show All

Lid or door won’t close

Fixed by
these parts

Show All

Videos related to the KGCU483VSS00

Watch our pros, then fix it yourself.

Replacing the Range Temperature Sensor

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

bUILT IN OVEN NOT COMING UP TO TEMPERATURE

5 of 5 people found this instruction helpful.

Kenneth from BUFFALO, NY
Very Easy
15 - 30 mins
Screw drivers

Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and conne ... Read more

Read less

Was this helpful?

replace pads or feet on steel grate of gas stove

4 of 4 people found this instruction helpful.

RICHARD from BROKEN ARROW, OK
Very Easy
Less than 15 mins

pull old ones out of legs. need to glue new ones in, they fit too loose. Some kits contain glue. get some high temp head gasket cement. a drop on each one is plenty. I used some old porcelain glue and hope it will hold. the pads are 2 bucks each plus shipping so don't let them get away!!!

Was this helpful?

All elements would heat to around 200 degrees, then stop

3 of 3 people found this instruction helpful.

frank from Wilmington, NC
Really Easy
15 - 30 mins
Screw drivers

Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.

Was this helpful?