KCMS185JSS (AS1EKAD) LG Wall Oven - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Time Delay Fuse – Part Number: 3B74133Q
$13.15
In Stock
Magnetron – Part Number: 6324W1A001L
$120.07
In Stock
Magnetron
Part #6324W1A001L
TRAY,GLASS – Part Number: 3390W1G009D
$72.55
In Stock
TRAY,GLASS
Part #3390W1G009D
This glass tray provides a stable, heat-resistant surface for cooking or heating while allowing even energy distribution. It is replaced when chipped, cracked, or missing to restore safe operation.
Motor Synchronous – Part Number: 6549W1S011B
$46.15
On Order
Motor Synchronous
Part #6549W1S011B
High Voltage Diode – Part Number: 6021W3B001V
$21.95
In Stock
High Voltage Diode
Part #6021W3B001V
HOLDER ASSEMBLY,LOCKER – Part Number: 3501W1A053A
$57.15
Special Order
HOLDER ASSEMBLY,LOCKER
Part #3501W1A053A
Screw,Taptite – Part Number: 1SBF0402418
$13.15
Special Order
Screw,Taptite
Part #1SBF0402418
Thermostat – Part Number: 6930W1A003A
$17.55
Special Order
Thermostat
Part #6930W1A003A
Screw,Customized – Part Number: 4B70188C
$13.15
In Stock
Screw,Customized
Part #4B70188C
Lamp,Incandescent – Part Number: 6912W3B002L
$27.95
In Stock
Lamp,Incandescent
Part #6912W3B002L
Cap,Base Plate – Part Number: 5006W3A016B
$12.04
Special Order
Cap,Base Plate
Part #5006W3A016B
Sensor Assembly – Part Number: 6501W1A006A
$59.35
Special Order
Sensor Assembly
Part #6501W1A006A

Common Symptoms of the KCMS185JSS

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Motor Burned Out On Turntable
37 of 49 people found this instruction helpful.
  • Steven from Oak Forest, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
My 8 year old daughter cleaned the inside of the microwave with enough water to rival a tsunami. Resulted in a clean microwave with a fried out motor that no longer revolved. Part came quickly. Took cover and bottom off to get to the part. One screw held it on and a plug. Removed those, put on new part and she was good to go. No tri p to home depot today.
Was this helpful?
Thank you for voting!
Magnitron failed
8 of 13 people found this instruction helpful.
  • Joseph from WILTON, NH
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover .
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.
Was this helpful?
Thank you for voting!
Defective door interlock switches
6 of 9 people found this instruction helpful.
  • James from DELTA, CO
  • Very Easy
  • 15 - 30 mins
  • Pliers
Removed each switch (3) and checked them with multi-meter; got intermittent readings on two of the three. Also broke of a piece of the frame that holds the switches trying to remove them (old, exposed to heat and moisture over the years caused the plastic to become brittle and the wiring connectors were also hard to disconnect probably be cause of heat and moisture over the years).
Went to PartSelect web site and discovered the three switches and frame were bundled in to one part number, 43501A. So, I called and spoke with a very knowledgeable technician and she explained why plus helped me order the part over the phone. When I received the part, the switches were already mounted in the frame and the frame was modified compared to the OEM frame. As I began to remove the old frame, I discovered why the new frame was modified. It was as if PartSelect had done many of these door interlock repairs and they knew exactly where and how to modify the frame and communicated this with the manufacturer, because the new frame installation was very easy, there was nothing hard about installing the new frame with the switches already in place. I then reconnected the wiring to the switches and tested the microwave and it works fine now, Problem solved, Thanks PartSelect.com
Was this helpful?
Thank you for voting!